troubleshooting
7
If your appliance is not working properly, it may be a minor problem, therefore check the following:
Problem
Cause
Solution
Appliance is not functioning; light
does not work
- Appliance is not plugged in
- There is a power failure
- The thermostat is set on
●
- Plug the appliance in
- Check the fuse box
- Set the thermostat on setting 1-5
Temperature inside the
appliance is too high or too low
Thermostat has been set
incorrectly
Set the thermostat correctly
Air circulation vents are blocked
Clean the ventilation openings
Water is running out of the
appliance
Drain outlet is blocked
Clear the drain outlet with a skewer
Appliance is excessively noisy
Has the appliance been installed
correctly?
Check the installation
Are the pipes at the back touch-
ing or vibrating?
Check it and move the appliance forwards
The inside light is not working
Lamp is defective
Replace the bulb following the instructions
Note:
gurgling and hissing noises due to expansion in the refrigerant circuit are normal.
installation instructions
8
Before installation, read the instructions carefully.
• Fit the appliance only in stable kitchen units.
• If necessary, reverse the door according to the instructions.
• Check built in dimensions of your model according to the dimensions in figure A.
1 Remove the screw
5
on the top of the appliance, place the top bracket
6
and fix the bracket with the screw
5
(Figure B).
2 Take out the gasket
11
located on the side panel and remove the protective tape. Stick the gasket on the reverse side of the door
hinges of the appliance (Figure C).
3 The height of the appliance can be adjusted with the adjustable feet to fit the height of the cabinet (Figure D).
4 Slide the appliance into the kitchen cabinet and align the hinge surface with the front surface of the kitchen cabinet (Figure E).
5 Screw the hinges and metal bracket to the kitchen cabinet using the screws
1
(Figure F).
6 Unscrew and remove the nuts and washers from the appliance door. Place the door hang on the appliance door by inserting
the holes to adjustment bolts (Figure G).
Dimension B =
measure from the underside surface of kitchen cabinet to the bottom of the door hang.
Dimension C =
measure from the underside surface of the kitchen cabinet to the top of the next cabinet door.
7 Substract C from B and place the door hang
2
using this dimension for the vertical position and place to the center of the horizontal
position. Screw the door hang
2
using the screws
1
(Figure H).
8 Place the cabinet door onto the appliance door by inserting the adjustment bolts into the slots on the door hang. Place the washers
and screw the nuts onto the adjustment bolts (Figure I).
9 Close the door and check the alignment with the other cabinet doors. Make the adjustment of the unit door by screwing or
unscrewing the adjustment bolts for vertical adjustment and with the aid of the slots on the door hang for other directions. Tighten
the nuts to fix the bracket (Figure J).
10 Remove the screws at the bottom of the appliance door. Place the door bottom fixings
3
and screw the fixings to the appliance door
and the cabinet door (Figure K).
11 Slide the hang cover
4
onto the door hang (Figure L).
12 Position the plinth providing a gap with a minimum of 25 mm between the cabinet door and fix it (Figure M).
28
•
English
Summary of Contents for IKK0821D
