TROUBLESHOOTING TIPS
Malfunctions
Unit does not
start
Unit not cooling
or heating
(Cooling/ heating
models only)
room very well
while air flowing
out from the air
cond tioner
i
Cause
Power cut
Unit may have become Unplugged.
Fuse may have blown.
Battery in Remote controller may
have been exhausted.
The time you have set with timer
is incorrect.
Wait for power to be restored.
Check that plug is securely in wall
receptacle.
Replace the fuse.
Replace the battery.
Wait or cancel timer setting.
Set temperature correctly. For
detailed method please refer to
"
"
Using remote control section.
Clean the air filter.
Close the doors or windows.
Clear obstructions away first, then
restart the unit.
Wait.
Inappropriate temperature
setting.
Air filter is blocked.
Doors or Windows are open.
Air inlet or outlet of indoor or
outdoor unit has been blocked.
Compressor 3 minutes
protection has been activated.
If the trouble has not been corrected, please contact a local dealer or the nearest customer
service center. Be sure to inform them of the detailed malfunctions and unit model number.
Notes: Do not attempt to repair the unit yourself.
Always consult an authorized service provider.
What should be done?
TROUBLESHOOTING TIPS
Troubleshooting guide
8. Dripping water may generate on the surface of the indoor unit when cooling in a high
relatively humidity (relative humidity higher than 80%). Adjust the horizontal louver to
the maximum air outlet position and select HIGH fan speed.
9.
The air conditioner draws in heat from the outdoor unit and releases it via the indoor unit
during heating operation. When the outdoor temperature falls, heat drawn in by the air
conditioner decreases accordingly. At the same time, heat loading of the air conditioner
increases due to larger difference between indoor and outdoor temperature. If a
comfortable temperature can't be achieved by the air conditioner, we suggest you use a
supplementary heating device.
10.
Power failure during operation will stop the unit completely.
For the unit without Auto-restart feature, when the power restores, the OPERATION indicator
on the indoor unit starts flashing. To restart the operation, push the ON/OFF button on the
remote controller. For the unit with Auto-restart feature, when the power restores, the unit
restarts automatically with all the previous settings preserved by the memory function.
Heating mode (For cooling and heating models only)
Auto-restart function
7.
The air conditioner runs
function after turning off the unit.
When turning off the unit under COOL(AUTO COOL, FORCED COOL) and DRY mode, the air
conditioner will run
function for 7-10 minutes,
then stop the operation and turn
off the unit automatically.
Anti-mildew
Anti-mildew
if turns off on HEAT mode, the unit will
continue operating for about 30 seconds at LOW fan speed,
Under Anti-mildew operation, do not restart the air conditioner until the
unit is completely off.
Fuse blows frequently or circuit breaker trips
frequently .
Other objects or water fall into the air conditioner.
Terrible odors are smelled or abnormal sounds
are heard.
Trouble
OPERATION(RUN) indicator or other
indicators continue flashing.
If one of the following code appears on the
display area : E0,E1,E2,E3.....or P0,P1,P2,
P3...., or F1,F2,F3.......
The unit may stop operation or
continue to run in a safety condition
(depending on models). Waiting for
about 10 minutes, the fault may be
recovered automatically, if not,
disconnect the power and then
connect it in again. If the problem
still exists, disconnect the power and
contact the nearest customer service
center.
Stop the air conditioner immediately,
disconnect the power and contact the
nearest customer service center.
After 240 hours of operation, the indoor display window will display and flash
CL ,
this feature is a reminder to clean the Air Filter for more efficient operation. After 15
seconds, the system will revert back to the previous display again. When the
CL
indicator appears and flashes, please press the LED button on remote controller
for 4 times or press the Manual control button for 3 or more times to clear the registered
hours, otherwise the CL indicator will display and flash again for another 15 seconds at
the next time of starting the unit.
11. Cleaning filter reminding function(Optional)
,
,
,
,
,
,
After 2880 hours of operation, the indoor display window will display and flash
nF ,
this feature is a reminder to replace the Air Filter for more efficient operation. After 15
seconds, the system will revert back to the previous display again. When the
nF
indicator appears and flashes, please press the LED button on remote controller for 4
times or press the Manual control button for 3 or more times to clear the registered hours,
otherwise the nF indicator will display and flash again for another 15 seconds at the
next time of starting the unit.
12. Replacing filter reminding function (Optio nal )
,
,
,
,
,
,
