background image

43

WARRANTY AND GUARANTEE

43

iV-Smart+ ventilation device | Installation instructions

Warranty and guarantee

Warranty

Outside Germany, the national warranty provisions of the country in which the system is sold 

apply. Please contact the distributor for your country.

The warranty covers all defects that were present at the time of purchase. Failure to observe the 

intended use will invalidate all warranty claims.

Manufacturer guarantee

inVENTer GmbH provides a five-year warranty for all electrical components and the wall sleeve, 

as well as a 30-year warranty on the ceramic component of the thermal accumulator.  

This covers premature product wear.

Further information about the warranty is available at www.inventer.eu/guarantee

Service

Claims

Check the delivery for completeness and transport damage upon receipt using the delivery note. 

Report missing items immediately, and at the latest within 14 days to your supplier, distributor or 

factory representative.

Warranty and guarantee claims

In the case of a warranty or guarantee claim, contact your local distributor or factory  

representative.

In all cases, please return the complete device to the manufacturer.  

The warranty is an additional offering by the manufacturer and in no way affects the applicable 

law.

Accessories and spare parts

To order components for your ventilation device, contact your nearest distributor or our service 

staff.

Technical customer service

For technical support contact our service staff:

 

+49 (0) 36427 211-0

 

+49 (0) 36427 211-113

 [email protected]

 http://www.inventer.eu

Summary of Contents for iV-Smart Plus













































Reviews: