Invacare Lightweight Aluminum Wheelchai Owners Operating & Maintenance Manual Download

Page: 13 / 24

CALL TOLL FREE, 1-888-6AURORA

(628-7672)

QUESTIONS ABOUT THIS PRODUCT?

This Procedure includes the following:

Swingaway Footrest Assembly Installation

Swingaway Footrest Height Adjustment

Heel Loop Replacement

1. Remove the hex screw and coved washer that se-

cure the lower footrest assembly to the upper foot-
rest support.

2. Reposition the lower footrest assembly to the desired

height. Line up the mounting holes in the lower foot-
rest assembly and the upper support.

3. Securely tighten the hex screw and coved washer.

4. Repeat this procedure for the other footrest, if neces-

sary.

PROCEDURE 1

FOOTRESTS

WARNING

After making adjustments, always make
sure that parts are properly tightened BE-
FORE using the wheelchair.

SWINGAWAY FOOTREST ASSEMBLY
INSTALLATION (FIGURE 1)

1. Turn the footrest to the side (open footplate is perpen-

dicular to wheelchair).

2. Install the mounting pin on the footrest onto the mount-

ing tube on the wheelchair frame.

3. Push the footrest towards the inside of the wheel-

chair until it locks into place.

NOTE: The footplate will be on the inside of the wheelchair
when locked in place.

4. Repeat this procedure for other footrest assembly.

5. To release the footrest, push the footrest release le-

ver inward, rotate footrest outward.

SWINGAWAY FOOTREST HEIGHT
ADJUSTMENT (FIGURE 2)

NOTE: Release the footrest locking mechanism and lift
the footrest off of the mounting tube. Lay the assembly on
a flat surface to simplify this procedure.

FIGURE 1 - SWINGAWAY FOOTREST

ASSEMBLY INSTALLATION

Hex Screw/Coved Washer

Phillips Screw

Spacer

Locknut

FIGURE 3 - HEEL LOOP REPLACEMENT

Mounting Pin

Footrest
Release

Lever

Mounting

Tube

Swingaway

Footrest

Assembly

Slide Tube

HEEL LOOP REPLACEMENT (FIGURE 3)

1. Remove the hex screw and coved washer that se-

cure the lower half of the footrest to the upper support.

2. Remove the lower footrest assembly.

3. Remove the phillips screw and locknut that secure

the heel loop to the footrest.

4. Slide heel loop over slide tube of footrest assembly.

5. Replace heel loop.

6. Reverse STEPS 1-5 to reassemble.

NOTE: When securing the heel loop to the footrest as-
sembly, tighten the phillips screw and locknut until the
spacer is secure.

Hex Screw

Coved Washer

Footrest

FIGURE 2 - SWINGAWAY FOOTREST

HEIGHT ADJUSTMENT

O
O

E
S

Summary of Contents for Lightweight Aluminum Wheelchai

























Search results

Summary of Contents for Lightweight Aluminum Wheelchai

Reviews:

Related manuals for Lightweight Aluminum Wheelchai

Brands by name

Popular brands

Invacare Lightweight Aluminum Wheelchai, Owners Operating & Maintenance Manual

Search results

Summary of Contents for Lightweight Aluminum Wheelchai

Reviews:

Related manuals for Lightweight Aluminum Wheelchai

Brands by name

Popular brands