Invacare 5410VC User Manual & Entrapment Manual Download Page 3

3

PLEASE READ ALL WARNINGS/CAUTIONS BEFORE USE

 

·

 

DO NOT

or explosive gases.

 

·

 

equipment other then nasal or masked type.

 

·

  When using nasal or masked type administering equipment, 

oxygen or air tubing 

MUST

 be routed and secured properly to 

ensure that tubing does 

NOT

 become entangled and eventually 

severed during normal operation of  Electric bed

.

 

·

  Liquids can cause electrical hazards. In the event of a spill in or 

around the bed, immediately unplug the bed and allow the area 

to dry thoroughly before plugging in the bed. If a spill occurs, 

UNPLUG

 the bed immediately. Clean up spill and allow bed or 

area to dry thoroughly before using the electric controls again.

 

·

  This bed is designed for adults only. 

DO NOT

 use with or for 

children. Children must be closely supervised at all times when near 

the bed.

·

  Users who are unable to understand or follow these instructions 

and warnings or who have limited physical capabilities should be 

supervised or assisted while using the bed.

·

 

NEVER PERMIT ANY ONE UNDER THE BED AT ANYTIME

.

 

·

  When operating or moving the bed, 

ALWAYS

 ensure that the 

individual utilizing the bed is positioned properly within the 

 

·

 

ALWAYS

 keep clear of moving parts when adjusting the bed. 

Patient should be centered on the bed with extremities within the 

mattress area. 

DO NOT

 allow extremities to extend beyond the 

sides or between bed rails.

WARNINGS

.

 

·

 

DO NOT

 use this bed for patient transport. 

DO NOT

 move the bed 

while occupied, otherwise injury or damage may result.

·

  The maximum safe working load of this bed (patient, mattress, 

bedding, and accessories) is 450lbs/204kg. The maximum user weight is 

350lbs/158kg. 

ALWAYS

 observe the weight limits.

·

 

DO NOT

 stand or climb on bed.

·

  Bed is intended for a single occupant. 

NEVER

 allow more than one 

person to sit or lay on bed at the same time.

·

  To prevent patient injury due to falls, 

ALWAYS

 leave bed at lowest height 

when the patient is unattended.

·

  Inappropriate handling of the power cord can create an electrical hazard.

   

Regularly inspect cord and plug for damage such as kinking 

 

or fraying; 

DO NOT

 use if cord or plug is damaged, contact   

 

your dealer for repair or replacement.

   

DO NOT

 unplug by pulling on the cord, this may damage 

 

the plug connection. 

NEVER

 pull, jerk, twist, or severely 

 

bend the cord, especially near the plug connection.

   

DO NOT

 use this product with power strips or extension cords. 

 

DO NOT

 overload wall outlets. 

ALWAY

S connect this product to an  

 

appropriate voltage outlet; 

DO NOT

 use with a DC to AC converter.

·

 

ALWAYS

 take care when routing power cords for accessories or other 

equipment through the space under the bed. Cords should be secured 

such that they cannot become pinched or damaged by moving parts of 

the bed. Damaged cords should 

NOT

 be used.

·

  It is the responsibility of the patient’s physician and caregiver to assess 

the patient and determine which devices and accessories are needed 

to support and protect the patient, while limiting risk to the patient. 

Use of fall protection, pressure management, and transfer assistance 

mechanisms should be considered as appropriate.

·

 

DANGER!

 Entrapment may cause patient injury or death.

warnings continued on next page

Summary of Contents for 5410VC



















Reviews: