background image

5

1. Connect the spade connector wires to the motor

in the following manner:

A. BLACK spade connector wire to lower spade.

B. RED spade connector wire to upper spade.

CAUTION

DO NOT secure the pendant cable be-
yond the middle of the cable (measur-
ing from the current limit device to the
pendant), otherwise damage to the
cable may result.

.

2. Secure the pendant cable and the spade connec-

tor wire wrap to the motor with the mounting bracket
as shown in FIGURE 8.

3. Align the mounting holes of the mounting bracket and

motor and secure the mounting bracket with the two
(2) EXISTING mounting screws. Tighten securely.

4. Position the motor shroud over the motor, aligning  the

mounting holes of the motor shroud and motor.

5. Install the machine screw and washer in the side

mounting hole. Tighten securely.

6. Install the two (2) self-locking screws and two (2)

washers in the front mounting holes. Tighten securely.

7. Grasp the handgrip on the battery pack and push

downwards to install it onto the motor shroud.

WARNING

To prevent frame from tipping when raising
the bath lift without the seat installed, ei-
ther suction the frame to the floor or place
one foot on the frame base.

8. Secure the frame to the floor with the suction cups or by

standing on the frame base.

9. Test the operation of the bath lift by pressing the

UP and DOWN buttons on the pendant to ensure
proper installation of the NEW pendant.

10. Perform one (1) of the following:

PROPER OPERATION -  Install the bath lift
frame into the bathtub. Refer to INSTALLING
BATH LIFT INTO THE BATHTUB in this in-
struction sheet.

IMPROPER OPERATION - If the bath lift does
not respond correctly when the pendant but-
tons are pushed (for example, the lift raises
when the DOWN button is pushed) or if it does
not work at all, repeat STEPS 1-9 making sure
the spade connectors are properly connected.

NOTE: If improper operation exists, contact
Invacare at the number on the back of this in-
struction sheet before using.

FIGURE 7 - INSTALLING THE BATTERY

CONNECTOR

DETAIL "F" - STEP 5

DETAIL "E" STEPS 2-3

TIGHTEN

Flathead Screw (DO

NOT REMOVE)

Bare

End of

Wire

Insulated

Wire

BLUE (-)

Wire

 Flared End of Battery Connector

YELLOW

(+) Wire

Flat Screws

STEPS 8-10

Yellow (+) Wire

Blue (-) Wire

FRONT

Hole

REAR Hole

REAR of

Motor

Shroud

FRONT of

Motor

Shroud

DETAIL "D" - STEP 1

Mounting

Screws

(Nuts NOT

SHOWN)

Battery

Connector

BLUE (-)

Wire

YELLOW (+) Wire

Flared End

Battery

Connector

NEGATIVE

(-) Channel

POSITIVE (+)

Channel

Installing the Motor Shroud (FIGURE 8)

CAUTION

The spade connectors MUST be con-
nected to the motor as shown in FIG-
URE 8 - otherwise, the pendant will op-
erate improperly.

Summary of Contents for 1085144









Reviews: