background image

 

 

 

 

 

Open-Q™ 835 Development Kit based on the 

Snapdragon™ 835 (APQ8098) Processor 

User Guide 

 

[Document: ITC-01IMP1283-UG-001 Version: 1.0] 

 

Your use of this document is subject to and governed by those terms and conditions in the Intrinsyc Purchase an  Open-Q™ 835 
Development Kit based on the Snapdragon™ 835 (APQ8098) Processor  and Software License Agreement for the Open-Q 835 
Development Kit, which you or the legal entity you represent, as the case may be, accepted and agreed to when purchasing an Open-Q 
Development Kit from Intrinsyc Technologies Corporation (“

Agreement

”).      You may use this document, which shall be considered part 

of the defined term “Documentation” for purposes of the Agreement, solely in support of your permitted use of the Open-Q 835 
Development  Kit  under the Agreement. Distribution of this document is strictly prohibited without the express written permission of 
Intrinsyc Technologies Corporation and its respective licensors, which they can withhold, condition or delay in its sole discretion. 
 
Intrinsyc is a trademark of Intrinsyc Technologies Corporation., registered in Canada and other countries. 
Qualcomm® and Snapdragon™ are trademarks of Qualcomm® Incorporated, registered in the United States and other countries. Other 
product and brand names used herein may be trademarks or registered trademarks of their respective owners. 

 

This document contains technical data that may be subject to U.S. and international export, re-export, or transfer (“export”) laws. 
Diversion contrary to U.S. and international law is strictly prohibited. 

Summary of Contents for Open-Q 835











































Reviews: