2
APPLICATION:
The document shredder
INTIMUS 0077SL /
0077SF / 0077SE
is a machine for the destruc-
tion of common written material.
The machine may only be used to
shred paper!
Shredding of other types of data carriers
and of staples and paper clips may
lead to injuries (for example due to
splintering of hard materials etc.) and
damage to the machine (for example
destruction of the cutter etc.).
The air vents in the housing are ne-
cessary for cooling and may not be
covered or closed!
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
INSTALLATION:
- Unpack and set machine upright.
- Place plastic or paper sack into the receptacle.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL DATA“.
OPERATING FUNCTIONS:
1 = Rocker switch „ready“ (fig. 1)
Depress this switch to start the machine or
to stop the machine.
2 = „Cutting system forward“
pushbutton (fig. 2)
Pressing this button starts the cutting
system. Material can now be fed to the
shredder.
3 = „Cutting system stop“
pushbutton (fig. 2)
Pressing this button switches the shredder
off, thereby halting the cutting system.
4 = „Cutting system reverse“
pushbutton (fig. 2)
Pressing this button starts the cutting
system in reverse.
5 = Pilot lamp „ready“ (fig. 2)
Lights when the rocker switch (1) is opera-
ted.
6 = Pilot lamp „receptacle full“ (fig. 2)
Lights as soon as the receptacle is full and
needs to be emptied. At the same time the
machine switches off automatically.
7 = Pilot lamp „door open“ (fig. 1)
Lights when the door is not closed. The
machine then switches off automatically
and it cannot be started as long as the door
is open.
8 = Light barrier (forward operation) (fig. 3)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
OPERATING THE MACHINE:
To start, switch on the unit by operating the
rocker switch (1) (fig. 1).
The pilot lamp marked „ready for operation“
(5), as well as the red stop-button „S“ (3) (fig. 2)
will light to indicate that the machine is ready
for operation.
The paper tray may not be used as
a step ladder or as a seat. Danger of
tipping over!
FEEDING PAPER:
- Feed paper through the inlet guide to the
cutting system.
- Machine switches automatically to forward
and draws paper in.
- The machine switches off automatically after
shredding.
Note:
In order to always obtain a correct
cutting result in terms of particle size and
thus achieve the safety class according to DIN
32757 as stated in the brochure, the material
to be cut must always be fed into the cutting
mechanism at a right angle to the cutting
mechanism and in appropriate quantities in
the middle of the inlet slot.
Never feed the shredder with a quan-
tity of paper exceeding the maximum
indicated in the technical details.
Should the machine be overfed, follow
the instructions under „AUTOMATIC
RESPONSE IN CASE OF OVERLOADING“.
EMPTYING THE RECEPTACLE (Fig. 4):
When the receptacle is full, the machine turns
off automatically and a horn sounds. The pilot
lamp (6) (fig. 2) lights up. Empty the receptacle
as follows:
- Open door. The pilot lamp (7) (fig. 2) lights
up.
- Pull the receptacle out of the machine.
- The horn stops. The pilot lamp (6) goes off.
- Remove the full sack and dispose of contents.
- PLace empty sack into receptacle, push in the
receptacle and close door. The pilot lamp (7)
goes off.
Note:
The machine will only run with closed
door!
INITIAL START UP
OPERATION
fig. 1
fig. 4
fig. 2
fig. 3
8
S
3
2
5
6
7
4
1
93584 2 11/19
0077SL/SF
0077SE
