background image

128

GS

SAVE THESE INSTRUCTIONS

Page 3

(128GS)  MODEL SF20220R SAND FILTER PUMP  ENGLISH  7.5” X 10.3”  PANTONE 295U  10/28/2011

English

SS

AA

FF

EE

TT

YY

 RR

UU

LL

EE

SS

WARNING

IMPORTANT SAFETY RULES

Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.

READ AND FOLLOW ALL INSTRUCTIONS

• To reduce the risk of injury, do not permit children to use this product. Always 

supervise children and those with disabilities.

• Children must stay away from this product and electrical cord(s).
• Children should be supervised to ensure that they do not play with the appliance.
•  This appliance is not intended for use by persons (including children) with reduced 

physical, sensory or mental capabilities, or lack of experience and knowledge. They 
must at all times be supervised by a knowledgeable and experienced adult 
responsible for their safety.

• Assembly and disassembly by adults only.
• Risk of electric shock. Connect this product only to a grounding type receptacle 

protected by a ground-fault circuit interrupter (GFCI) or residual current device 
(RCD). Contact a qualified electrician if you cannot verify that the receptacle is 
protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, 
which has a maximum rate of 30mA. Do not use a portable residual current device 
(PRCD).

• Always unplug this product from the electrical outlet before removing, cleaning, 

servicing or making any adjustment to the product.

•  The plug must be accessible after produc   t is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by 

lawn mowers, hedge trimmers and other equipment.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service 

agent or similarly qualified persons in order to avoid a hazard.

• To reduce the risk of electric shock, do not use extension cords, timers, plug 

adaptors or converter plugs to connect unit to electric supply; provide a properly 
located outlet.

• Do not attempt to plug in or unplug this product while standing in water or when 

your hands are wet.

• Keep this product more than 2m away from the pond.
• Keep the plug of this product more than 3.5m away from the pond. 
• Position this product away from the pond, so as to prevent children from climbing 

on it and accessing the pond.

• Do not operate this product when pond is occupied.
• To reduce the risk of entrapment hazard, never enter the pond if suction strainer 

component is loose, broken, cracked, damaged or missing. Replace loose, broken, 
damaged, cracked or missing suction strainer components immediately.

• Your body or hair may be trapped causing permanent injury or drowning.
• To prevent equipment damage and risk of injury, always turn pump off before 

changing the filter control valve position.

• Never operate this product above the maximum working pressure stated on the 

filter tank.

• Hazardous Pressure. Improper tank valve cover assembly could cause the valve 

cover to blow off and cause serious injury, property damage or death.

• This product is intended to be used only for the purposes described in the manual!

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.

These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and 
danger. Please use common sense and good judgement when enjoying any water activity.

Summary of Contents for SP20220





















Reviews: