background image

192

PO

S  AVE  THESE  INSTRUCTIONS

(192PO)  SPA  ENGLISH  7.5” X 10.3”  PANTONE 295U  04/18/2013

English

Page 4

j)  Exit immediately if uncomfortable, dizzy, or sleepy. Spa heat can cause hyperthermia and unconsciousness.  

  The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia. The causes,   

  symptoms, and effects of hyperthermia may be described as follows:

  Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the  

  normal body temperature of 98.6°F (37°C). The symptoms of hyperthermia include an increase in the 

  internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia

  include failure to perceive heat; failure to recognize the need to exit spa or hot tub; unawareness of 

  impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and 

  unconsciousness resulting in the danger of drowning.

•  People with infectious diseases should not use a spa or hot tub.

•  To avoid injury exercise care when entering or existing the spa or hot tub.

•  Always add chemicals to water, never add water to chemicals. Adding water to chemicals may cause    

  strong fumes or violent reactions and hazardous chemical spray.

•  Never jump or dive into a spa or any shallow body of water.

•  Assembly and disassembly by adults only.

•  Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any    

  adjustment to the product.

•  The plug must be accessible after product is installed.

•  Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge    

  trimmers and other equipment.

•  If the supply cord is damaged, it must be replaced by a qualified electrician in order to avoid a hazard. Use  

  only identical replacement parts when servicing.

•  To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to  

  connect unit to electrical supply; provide a properly located outlet.

•  Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.

•  Do not leave the spa empty for extended period of time. Do not expose the spa under direct sunshine.

•  Adequate drainage system must be provided around the spa to deal with overflow water.

•  Do not allow the water in the spa to freeze. Do not turn on the spa when the water is frozen.

•  Do not use the spa if damaged in delivery and/or malfunctioning in any fashion. Contact the Intex service  

  center for further direction.

•  Never pour water with a temperature higher than 104°F (40°C) into the spa directly.

•  Keep all pets away from spa to avoid any damage.

•  Do not add bath oil or bath salt to the spa water.

WARNING

CAUTION

•  Maintain water chemistry in accordance with manufacturer’s instructions.

•  This product is provided with a GFCI/RCD located at the end of the power cord. The GFCI/RCD must be  

  tested before each use. Do not use the spa if the GFCI/RCD does not function properly. Disconnect the

  power cord until the fault has been identified and corrected. Contact a qualified electrician to correct the   

  fault. Do not bypass the GFCI/RCD. There are no serviceable parts inside the GFCI/RCD. Opening the    

  GFCI/RCD will void the warranty.

1.

  Plug the power cord into a grounded electrical socket.

2.

 Press the 

RESET

 button on the GFCI/RCD

.

 

3.

 Turn on the spa electrical equipment.

4.

 Press the 

TEST

 button on the GFCI/RCD

.

 

The GFCI/RCD indicator 

  should turn off and the electrical equipment should shut off. If the 

  GFCI/RCD indicator does not turn off, and the electrical equipment 

  does not shut off, the GFCI/RCD is faulty. Do not use the spa. 

  Contact a qualified electrician to correct the fault.

5.

 Press the 

RESET

 button on the GFCI/RCD. The indicator on 

  the GFCI/RCD should turn on. If the GFCI/RCD indicator does 

  not turn on, the GFCI/RCD is faulty. Do not use the spa. 

  Contact a qualified electrician immediately to correct the fault.

WARNING

 

 

RESET

TEST

RESET

TEST

RESET

TEST

RESET

TEST

RESET

TEST

RESET

TEST

Summary of Contents for PureSpa SSP-10


















Reviews: