275
PO
S AVE THESE INSTRUCTIONS
(275PO) SPA (JET + HARD WATER) ENGLISH 7.5” X 10.3” PANTONE 295U 06/23/2015
English
Spa Tub Drainage
1.
Turn off and unplug the spa control unit.
2.
Connect the drain valve adaptor to a garden hose and point the other end
of the garden hose to a suitable draining area
(see drawing 12).
3.
Remove the drain valve cap from outside of the spa tub and attach the
drain valve adaptor to the drain valve
(see drawing 12).
4.
From inside of the spa tub, open the drain valve cap, water will start
fl
owing out from the garden hose.
5.
When the water stops draining, disconnect the spa control unit from
the spa tub wall. Lift the spa tub wall from the side opposite the drain,
leading any remaining water to the drain and emptying the spa completely
(see drawing 13).
6.
Turn over the spa tub to empty any remaining water
(see drawing 14).
7.
Unscrew the drain valve on the spa control unit side using a coin to drain
out any water
(see drawing 15).
8.
Use a clean towel to wipe up any remaining water and moisture on the
spa tub and spa control unit.
9.
Ensure the spa tub and spa control unit are thoroughly dried.
NOTE:
The enclosed plugs
(15 & 23)
can be used to cover the water inlet
and outlet connectors from the inside of the spa tub to prevent water from
fl
owing out.
Spa Tub Cleaning
If dirt is visible in the water or water becomes cloudy and proper water
chemistry does not clear it up, change the water and clean the spa tub.
See “Spa Tub Drainage” section on how to drain the spa.
While empty, remove the cartridge housing from inside of the spa tub wall,
clean and/or replace the
fi
lter cartridge. Use a sponge and mild soap solution
to wipe away any soil or stains on the inside of the spa wall. Rinse thoroughly
before re
fi
lling with clean water.
IMPORTANT:
Do not use steel wool, hard brushes or abrasive cleaners.
Spa Tub Air Valve Fastening
Check the spa tub air valve for leakage and tightness before use. If air is
leaking from the air valve, use the provided wrench
(22)
to tighten the air valve
as follow:
1.
Make sure the spa tub is de
fl
ated, open the air valve cap and insert the
wrench
(22)
into the air valve body
(see drawing 16).
2.
With one hand, hold the backside of the air valve base from the inside of
the spa tub wall and turn the wrench
(22)
clockwise.
IMPORTANT:
Never adjust the air valve base when the spa is in use or
fi
lled with water. Only use the air valve wrench if the air valve is loose or
there is leakage around air valve base. Do not over tighten the air valve:
over tightening can damage the valve. Just ensure the air valve is snug
and not leaking.
Spa Cover
The attachment buckles of the cover are locking buckles. Two keys are provided in the plastic bag with the
manual and other accessories. Each buckle is marked with “locked” and “unlocked” symbols for easy operation:
put the key into the slot on the buckle and turn it to the appropriate position to lock or unlock the buckle
respectively.
To assure safety from unauthorized access, always put the cover on when spa is not in use and lock all buckles.
Always keep the keys out of reach of children. In case you misplace the keys, you can use any similar size
fl
at
screwdriver to lock or unlock the buckles.
Inspect the spa cover regularly for leaks, premature wear and tear, damage, or signs of deterioration. Never use
a worn or damaged cover: it will not provide the level of protection required to prevent unsupervised access to
the spa by a child.
MAINTENANCE
Page 18
16
22
12
14
15
1
2
3
11
13
