background image

275

PO

S  AVE THESE INSTRUCTIONS

(275PO)  SPA (JET + HARD WATER)  ENGLISH  7.5” X 10.3”  PANTONE 295U  06/23/2015

English

Page 13

LED CODE CHART

E90

No water 

fl

 ow

• 

Turn off and unplug the control unit.

• 

Ensure the outlet cover grid is clean and free 

   from obstructions.

• 

Clean or replace the cartridge, see 

   Maintenance and Storage section.

• 

Ensure the in/outlet connections on the spa tub 

   and 

fi

 lter pump are not blocked.

• 

Keep the spa water properly sanitized  to 

   ensure a clean and unclogged 

fi

 lter cartridge.

• 

Press the      button to turn off the unit. Release 

   trapped air by unscrewing the drain valve cap 
   on the control base side with a coin.  Air has 
   been release once a steady stream of water is 
   

fl

 owing out from the drain valve. Wait for 15 

   seconds and screw the drain valve cap back. 
   Press the        button to activate the control 
   panel buttons, and then run the 

fi

 lter function 

   by pressing the         button to push out any 
   remaining air in the system.

• 

If problem persists, contact Intex Service   

   Center.

E94

Water temperature too low

  If the ambient temperature is below 39°F (4°C), 

   we recommend not to use the spa.

 Turn off and unplug the control unit, add some 

   warm water to raise the spa water temperature 
   above 41°F (5°C), then press the       button to 
   heat up the water to the desired temperature.

  If problem persists, contact Intex Service 

   Center.

E95

Water temperature too high

  Turn off and unplug the control unit. When the 

    water has cooled down, plug the GFCI/RCD 
    and restart all over again.

  Turn the heater off, then press the 

fi

 lter and jet 

  buttons to lower the water temperature.

  If problem persists, contact Intex Service 

   Center.

E96

System Error

  Turn off and unplug the control unit, use the 

   cap to stop the water from 

fl

 owing out of the 

   tub, disassemble and drain out the control unit. 
   Reassemble the control unit back to the tub. 
   Plug the GFCI/RCD and restart all over again.

  If problem persists, contact Intex Service 

   Center.

E99

Water temperature sensor broken

  Contact Intex Service Center.

END

After 72 hours of continuous heating 

operation, the pump will hibernate 

automatically. The rapid heating and 

water 

fi

 ltration functions are disabled.

  Press the water 

fi

 lter button to re-active the 

   

fi

 lter pump. 

LED Reading                      CAUSE                                         SOLUTION

Summary of Contents for PureSpa SPJ-H-11






















Reviews: