Intex ECO15220 Owner'S Manual Download

Page: 32 / 34

261A

SAVE THESE INSTRUCTIONS

(261IO) Sand Filter Pump & Saltwater System with Electrocatalysis Oxidation (14” & 16”) ENGLISH 7.5” X 10.3” PANTONE 295U 08/04/2014

English

Page 32

TROUBLESHOOTING GUIDE (continued)

LED PANEL

CODE

PROBLEM

SOLUTION

LED Panel Code Flash & Alarm On (

NOTE

: Always turn off the power before cleaning and servicing).

. Circulation line is blocked.

. Incorrect inlet and outlet hose

direction.

. Scale on the flow sensor.

. Flow sensor cord is loose.

. Device is set and operating in

backwash, rinse or waste mode.

. Flow sensor failure.

. Dirt or scale on titanium plates.

. Low salt level / No salt.

. Electrolytic cell cord is loose.

. Possible electrolytic cell failure.

. High salt level.

. Possible electrolytic cell failure.

. Display and all lights are off - the

system does not power up.

•

If your unit has plunger valves, ensure that they

are open.

•

Clear your basket and cell from debris and dirt.

See “Maintenance”.

•

Depress the 6-way valve,

elease all trapped air

in the circulation line.

•

Check the direction of the inlet and the outlet

hose. Reverse the hoses if necessary. See “Set

Up Instructions”.

•

Clean the flow sensor, paying special attention

to the hinge. See “Maintenance”.

•

Plug the flow sensor firmly into the flow sensor

receptacle.

•

Ignore the alarm, finish the backwash, rinse or

waste operation then turn the power switch OFF

and ON again to reset the alarm.

•

Contact Intex Service Center.

•

Remove the electrolytic cell for inspection. Clean

it if necessary. See “Maintenance”.

•

Add salt. See “Salt & Pool Water Volumes”.

•

Ensure that the cell cord is plugged firmly into

the cell housing receptacle.

•

Contact Intex Service Center. Replace the cell if

needed.

•

Partially drain the pool and refill it with fresh

water. See “Salt & Pool Water Volumes”.

•

Contact Intex Service Center. Replace the cell if

needed.

•

Household voltage is too high or too low

(+ 20%). Check the voltage is within the Range

stated on the device housing.

•

Contact Intex Service Center.

Summary of Contents for ECO15220



































Search results

Summary of Contents for ECO15220

Reviews:

Related manuals for ECO15220

Brands by name

Popular brands

Intex ECO15220, Owner'S Manual

Search results

Summary of Contents for ECO15220

Reviews:

Related manuals for ECO15220

Brands by name

Popular brands