IntesisBox DK-AC-MBS-1 Page 22 User Manual Download

Page: 22 / 23

DK-RC-MBS-1

User’s Manual r3.3

This information is subject to change without notice

IntesisBox

is a registered trademark of Intesis Software SLU

URL
Email
Phone

http://www.intesisbox.com

[email protected]
+34 938047134

22/23

258

The humidity sensor of return air sensor

259

Outdoor air humidity sensor error

260

Supply air temperature sensor error

261

Return air temperature sensor error

262

Outdoor air temperature sensor error

263

Remote controller temperature sensor error

267

Water leakage sensor 1 error

268

Water leakage sensor 2 error

269

Dew condensation error

339

Centralized remote controller PCB error

345

Communication error between centralized remote
control devices

347

Centralized remote control devices inappropriate
combination

349

Centralized remote controller address setting error

65535

(-1)

N/A

DK-RC-MBS-1

Error in the communication of DK-RC-MBS-1 with the
AC unit

In case to detect an error code not listed, contact your closest Daikin technical support service.

Summary of Contents for DK-AC-MBS-1
























Search results

Summary of Contents for DK-AC-MBS-1

Reviews:

Related manuals for DK-AC-MBS-1

Brands by name

Popular brands

IntesisBox DK-AC-MBS-1, User Manual

Search results

Summary of Contents for DK-AC-MBS-1

Reviews:

Related manuals for DK-AC-MBS-1

Brands by name

Popular brands