background image

 

 

TO ACCESS THE CONTROL PANEL

 

                                                                                                                                                                                                                                                                                                                         

 

 

                       

 

The  standby  switch,  located  at  the  top  right  hand  side  of  the  fireplace,  must  be  first 

switched on. 

 

It takes some time for the receiver to respond to the transmitter. Do NOT press the 

button more than once within two seconds for correct operation. 

 

Press once the button ON/OFF on the remote control turns ON/OFF the appliance and 

the fire effect. 

 

Press the DIMMER button to operate the dimmer mode. Each time the dimmer button 

is pressed, the intensity of the flame decreases. There are 5 levels of brightness you 

can cycle through, and the OFF setting. 

 

Press once the HEAT button for the low heat setting (750W); press twice for the high 

heat setting (1500W); press a third time to turn the heater off. 

 

Press the TEMP button to adjust the temperature. The highest temperature of the 

thermostat is 27.7°C (82

). There are several thermostat levels you can cycle through 

between 16.6°C (62

) and 27.7°C (82

), and the OFF settings. 

 

Press the TIMER button to cycle through the timer settings (1 hour, 2h, 3h, 4h, 5h, 6h, 

7h and 8h), and the OFF setting. 

Infrared Remote control 

 

-7- 

 

 

 

The remote control requires one 3V. CR2025 Lithium Cell Battery (included). 

Remove the protective film between the battery and the contacts in order for it to be 

operational (see Fig. 6 and Fig. 7). 

 

 

 

REPLACE THE REMOTE CONTROL BATTERY 

When the remote control stops operating or its range seems reduced, it is time to replace the 

battery with a new one. 

1.

 

The battery compartment is located on the back end of the remote. 

2.

 

Press and slide the battery door open and remove the old battery. 

3.

 

Insert a CR2025 battery, checking that the "+" and "-" terminals of the battery matches 

the schema inside of the battery compartment. 

4.

 

Replace the battery door. 

DO NOT mix old and new batteries. 

DO NOT use rechargeable silver oxide cell batteries with remote control unit. 

DO NOT mix alkaline, standard (Carbon-zinc) or rechargeable (Nickle-cadmium) batteries. 

DO NOT dispose of the batteries in a fire. Improper disposal may cause batteries to leak or 

explode. 

 

 

 

 

 

-8- 

 

Summary of Contents for 990-3075














Reviews: