background image

2

AN1260.1

January 26, 2010

Quick Setup Guide 

(Refer to Figure 1)

DO NOT APPLY POWER UNTIL STEP 6

For Cradle Input:

Step 1:

Connect a 5V supply PS1 to CRDL input 
(J1, upper +) with the current limit set at 
1.3A

Step 2:

Connect a 3.7V supply PS3 to BAT output 
(J3, upper +) with the current limit set at 
1.3A

Step 3:

Connect a current meter to JP6, as shown 
in Figure 1

Step 4:

Connect the DC electronic load of 1.2A to 
BAT (J3, upper +)

Step 5:

Insert a jumper shunt on JP1, all other 
jumper  shunts are not installed

Step 6:

Turn on Power Supplies and DC electronic 
load, adjust the power supply PS3 such 
that the voltmeter V2 reads 3.7V

Step 7:

Both the red and the green LEDs should 
be on, indicating power on and charging 
condition

Step 8:

The current meter I2 should read about 
0.28A as the charging current

Step 9:

Insert a jumper shunt on JP7 and the 

current meter I2 should read about 
0.575A charging current

Step 10: Insert a jumper shunt on both JP7 and 

JP8, the current meter I2 should read 
about 1.04A charging current

Step 11: Reduce the voltage at PS3 to 2.0V for 

trickle charge currents. Repeat Steps 8, 9 
and 10. The current reading should be 
52mA,103mA and 187mA for steps 8, 9 
and 10, respectively

Step 12: Slowly reduce the DC electronic load 

current until the green LED turns off. The 
current meter I2 should read about 47mA 
EOC current

Step 13: Insert a jumper shunt on JP5 and repeat 

Step 12, the current meter I2 should read 
93mA EOC current

For USB Input:

Step 1:

Connect a 5V supply PS2 to USB with the 
current limit set at 0.7A

Step 2:

Connect a 3.7V supply PS3 to BAT (J3 
upper +) with the current limit set at 0.7A

Step 3:

Connect the DC electronic load of 0.6A to 
BAT (upper +)

Step 4:

Connect a current meter to JP6 as shown 
in Figure 1

Step 5:

Install a jumper shunt on JP2 and a 
jumper shunt on JP4 to the USBON 
position, all other jumpers shunts are not 
installed

Step 6:

Turn on Power Supplies and DC electronic 
load, adjust the power supply PS3 such 
that the voltmeter V2 reads 3.7V

Step 7:

Both the red and the green LEDs should 
be on, indicating power on and charging 
condition

Step 8:

The current meter I2 should read about 
0.38A charging current

Step 9:

Reduce the voltage at PS3 to 2.0V for 
trickle charge current. Repeat Step 8. The 
reading should be around 80mA

Step 10: Slowly reduce the electronic load current 

until the green LED turns off, the current 
meter I2 should read about 55mA EOC 
current

Step 11: Insert a jumper shunt on JP5 and repeat 

Step 10. The current meter I2 should read 
75mA EOC current

Application Note 1260

Summary of Contents for ISL9214AEVAL1Z








Reviews: