background image

8

440 04 6001 00

Specifications  subject to change without notice.

Table 2 – Altitude Derate Multiplier for U.S.A.

ALTITUDE

PERCENT

OF

DERATE

 DERATE

MULTIPLIER

FACTOR*

FT.

 M

0–2000

 0

610

0

1.00

2001–3000

 610

914

4

6

0.95

3001–4000

 914

1219

6

8

0.93

4001–5000

 1219

1524

8

10

0.91

5001–6000

 1524

1829

10

12

0.89

6001–7000

 1829

2134

12

14

0.87

7001–8000

2134

2438

14

16

0.85

8001–9000

2438

2743

16

18

0.83

9001–10,000

2743

3048

18

20

0.81

*Derate multiplier factors are based on midpoint altitude for altitude range.

ON/OFF Switch

Regulator Seal Cap

Regulator Adjustment
Regulator Seal Cap under Cap

1/2” NPT Outlet

1/8” NPT Manifold
Pressure Tap

1/8” NPT Inlet
Pressure Tap

1/2” NPT Inlet

SINGLE-STAGE

A11153

Figure 3 

 

Gas Valve

R Y W G

10 TURNS

THERMOSTAT SUBBASE

TERMINALS WITH

THERMOSTAT REMOVED

(ANITICIPATOR, CLOCK, ETC.,

MUST BE OUT OF CIRCUIT.)

HOOK-AROUND

AMMETER

EXAMPLE: 5.0 AMPS ON AMMETER

10 TURNS AROUND JAWS

 

=  0.5 AMPS FOR THERMOSTAT

     ANTICIPATOR SETTING

FROM UNIT 24-V

CONTROL TERMINALS

A96316

Figure 4 

 

Amp. Draw Check with Ammeter

Summary of Contents for R9MSB0601716B




























Reviews: