manualshive.com logo in svg

INTERLUBE AX1, Service And Maintenance Manual

Share
Download
INTERLUBE AX1 Service And Maintenance Manual Download Page 13

13

7.3.4. Remove the six screws (13) and washers 

(14) from the bottom of the reservoir (12). 
Discard the old washers (14).

7.3.5. Carefully remove the reservoir (12) from 

the carcass ring (21). The mounting 
bracket (15) and O-ring (20) must be 
separated from the reservoir (12) and 
carcass ring (21). Discard the reservoir 
(12) and O-ring (20).

7.3.6. Carefully remove any old lubricant from the

lid moulding (5). Wipe the carcass ring 
(21) and AC mounting bracket (15) clean.

7.3.7. Set the reservoir (12) on the mounting 

bracket (15). Install the O-ring (20) onto 
the flange of the reservoir (12). Align the 
mounting holes.

WIRING DETAILS

7.3.8. Carefully install the reservoir / bracket /   

O-ring (12, 15, 20) onto the carcass ring 
(21). Align the mounting holes of all three 
pieces.

7.3.9. Install the six  new washers (14) and 

screws (13). 

Torque to 6 Lb-In/0.7Nm

.  

Do not over-tighten the screws (13).

7.3.10.Refer to 

7.2

above, and install the reservoir

paddle assembly.

7.3.11.Refer to 

7.1

, above, and install the 

reservoir lid assembly.

7.4. Wiring Diagrams.

AX1 & 2

M

M

N

L

P.C.B. MOUNTED

LED. (GREEN).

RED

BLUE

BLUE

BLUE

BROWN

BROWN

GREEN/YELLOW

GREEN/YELLOW

SEE TABLE

SEE TABLE

SEE TABLE

SPARE

1
2

3
4
5

Motor Voltage / Terminal

Block Wiring (50/60Hz).

110 Volt

240 Volt

RED

WHITE

BLUE

BLUE

WHITE

SPARE

1
2

RED

Pump must be earthed and fused.
110V - 1A
240V - 1A

Summary of Contents for AX1





















Reviews:

No comments

Brands by name

Popular brands

Load more brands