Interlogix TruVision Multi-Imager Installation Manual Download Page 2

Copyright 

© 2020  United Technologies Corporation,  

Interlogix is part of UTC 

Climate, Controls & Security

, a unit of United 

Technologies Corporation.  All rights reserved. 

Trademarks and patents 

T

rade names used in this document may be trademarks or registered 

trademarks of the manufacturers or vendors of the respective products.

 

Disclaimer 

Information in this document is subject to change without notice. No part of 

thi

s document may be reproduced or transmitted in any form or by any 

means, electronic or mechanical, for any purpose, without the express written 
permission of UTC Fire & Security Americas Corporation, Inc.

 

Manufacturer 

Interlogix. 
Authorized EU manufacturing representative: 

UTC Fire & Security B.V.

 

Kelvinstraat 7, 6003 DH Weert, The Netherlands 

Certification 

 

  

 

FCC compliance 

Class A: This equipment has been tested and found to comply with the limits 

for a Class A digital device, pursuant to part 15 

of the FCC Rules. These 

limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. 
This equipment generates, uses, and can radiate radio frequency energy 

and, if not install

ed and used in accordance with the instruction manual, may 

cause harmful interference to radio communications. Operation of this 

equipment in a residential area is likely to cause harmful interference in which 
case the user will be required to correct the interference at his own expense.

 

FCC conditions 

This device complies with Part 15 of the FCC Rules. Operation is subject to 

the following two conditions: 

 

(1) This device may not cause harmful interference.

 

(2) This Device must accept any interference rec

eived, including interference 

that may cause undesired operation.

 

ACMA compliance 

Notice! This is a Class A product. In a domestic environment this product may 
cause radio interference in which case the user may be required to take 

adequate measures. 

Canada 

This Class A digital apparatus complies with Canadian ICES

-003.  

Cet appareil numérique de la classe A est conforme à la norme NMB-0330 du 
Canada. 

Summary of Contents for TruVision Multi-Imager























Reviews: