background image

6

TruPortal Input Expansion Board Quick Reference

Status LEDs

Note the following details about Input Expansion board LEDs:

The VBUS yellow LED will flash on and off if there is no 
VBUS board communicating on the VBUS. If a VBUS board 
is present, the VBUS LED will remain off.

The green Power On LED stays on providing the operating 
voltage remains above 9.5 V. If the voltage is lower, the LED 
will flash on and off.

The two output LEDs follow when the outputs are active.

Serial Number Display

When the Input Expansion board is initially powered, the serial 
number is displayed in an encoded form. The number of times the 
VBUS yellow LED flashes while the green Processor OK LED 
stays on steady gives the digit value. 

For example, if the green LED is on and the yellow LED flashes 
three times, then the green LED goes off, the first digit is “3.” Then 
if the green LED turns back on and the yellow LED flashes nine 
times, then the green LED goes off, the second digit is “9,” etc.

“0” is indicated by the green LED turning on and the yellow LED 
not flashing. 

The entire serial number will be displayed, one digit at a time. It 
takes several seconds to complete the entire process. When the 
process is complete, the Processor OK green LED will flash on 
and off at a more moderate rate.

Specifications

The TP-ADD-IN-BRD is for use in low voltage, Class 2 circuits 
only. These specifications are subject to change without notice.

Power ratings 
-

Input: 12 VDC, 100 mA

-

Output: 12 VDC, 210 mA

Inputs: 16 inputs, standard EOL: 1k ohm in series, 1k ohm in 
parallel

Outputs: Two relay outputs 

Communication: SNAPP, VBUS

Cable requirements: 22 AWG (0.644 mm / 0.326 mm

2

), 

stranded
-

SNAPP bus: four conductors

-

VBUS: three conductors

-

Input wiring: two conductors

-

Power input: two conductors

Dimensions: 5.75 x 2.875 x 0.6 in. (146 x 73 x 15 mm)

Environmental
-

Temperature: +32 to +120° F (+0 to +49° C)

-

Humidity: 5—85% RHNC

-

BTU output: 4.1 BTU/hour

Certifications
-

UL294 Listed

-

FCC Part 15

-

CE marking

Regulatory Information

Contact Information

www.interlogix.com

Customer support: 

www.interlogix.com/support

© 25JUL13 United Technologies Corporation

Interlogix is part of UTC Climate Controls & Security, a unit of 
United Technologies Corporation.  All rights reserved.

Document number: 460803001C - July 2013

Manufacturer Interlogix 

Headquarters and Regulatory responsibility: 

Interlogix
3211 Progress Dr.
Lincolnton, NC 28092 USA 

EU authorized manufacturing representative: 

UTC Climate, Controls & Security B.V., 
Kelvinstraat 7, 6003 DH Weert, 
The Netherlands

Year of 
manufacture

The first two digits of the product serial number (located 
on the product identification label) are the year of 
manufacture.

North American 
standards

UL 294

FCC 
compliance

This device complies with part 15 of the FCC Rules. 
Operation is subject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) 
this device must accept any interference received, 
including interference that may cause undesired 
operation.

Certification  

European Union 
directives

We declare under our sole responsibility that this product 
is in conformity with Directive 1999/5/EC (R&TTE), 2004/
108/EC (EMC), 2006/95/EC (LVD), and 93/68/EEC 
(Marking) based on test results using harmonized 
standards in accordance with the Directives mentioned.

Summary of Contents for TruPortal TP-ADD-IO-BRD







Reviews: