background image

Copyright

 

© 2012 UTC Fire & Security Company. All rights 
reserved. 

Trademarks and

patents

 

Interlogix, IFS MC201-1P/1FS, the IFS Brand and 
logo are trademarks of UTC Fire & Security. 
Other trade names used in this document may be 
trademarks or registered trademarks of the 
manufacturers or vendors of the respective 
products. 

Manufacturer

 

UTC Fire & Security Americas Corporation, Inc. 
2955 Red Hill Avenue, Costa Mesa, CA 
92626-5923, USA 

Version

 

This document applies to IFS MC201-1P/1FS 
version 1.0. 

Certification

 

 

 

N4131

 

FCC compliance

 

Class A:

 This equipment has been tested and 

found to comply with the limits for a Class A digital 
device, pursuant to part 15 of the FCC Rules. 
These limits are designed to provide reasonable 
protection against harmful interference when the 
equipment is operated in a commercial 
environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if not 
installed and used in accordance with the 
instruction manual, may cause harmful 
interference to radio communications. Operation 
of this equipment in a residential area is likely to 
cause harmful interference in which case the user 
will be required to correct the interference at his 
own expense. 

ACMA 

compliance

 

Notice! 

This is a Class A product. In a domestic 

environment this product may cause radio 
interference in which case the user may be 
required to take adequate measures. 

European Union

directives

 

2004/108/EC (EMC directive)

: Hereby, UTC Fire 

& Security declares that this device is in 
compliance with the essential requirements and 
other relevant provisions of Directive 2004/108/EC

Summary of Contents for IFS MC201-1FS





















Reviews: