manualshive.com logo in svg

Intergraph Intense 3D Pro 2200, Installation Manual

Share
Download
Intergraph Intense 3D Pro 2200 Installation Manual Download Page 14

10

that you should use the Display option in the Control Panel to
select the preferred display resolution.  Click OK.

14.  If you want to change the display resolution or other display

settings, see the following section, “Configure the Video Display.”

CAUTION

When you select Display in the Windows NT Control Panel, a
message displays.  Click OK to close the message.  This message
displays every time you select Display unless you clear the Show
warning at startup check box.

For more detailed installation information, refer to the 

README

.

TXT

file delivered on the diskette containing the video display driver.

Configure the Video Display

Open Display in the Control Panel to view the Display Properties
dialog.  Use the dialog tabs to configure the operation of the
computer’s video display when it is controlled by the Intense 3D Pro
2200 Graphics Accelerator.  For example, click the Settings tab to
change the screen resolution, or click the Hardware Settings tab to
choose the monitor type.

NOTE

If you change any video attribute settings other than gamma
correction and screen resolution, you must restart the computer to
make the changes take effect.

For more detailed configuration information, refer to the 

README

.

TXT

file delivered on the diskette containing the video display driver.

Verify the Default Video Display Driver

After you configure the video display as desired, verify that the Intense
3D Pro 2200 video display driver is the default video display driver
that runs automatically when you start the computer.

To verify the default video display driver:

1.  In the Windows NT Control Panel, open System.

2.  In the System dialog, on the Startup/Shutdown tab, verify that

Windows NT Workstation Version 4.00 is selected in the Startup
list.  If it is not, select it from the list and click Apply.

3.  Click OK to close the System dialog.

NOTE

Do not select the “VGA mode” version of  the operating system.
The video display runs in VGA mode when the Intense 3D Pro
driver is not running.

Summary of Contents for Intense 3D Pro 2200



























Reviews:

No comments

Brands by name

Popular brands

Load more brands