Installation Guide
Î
Do not use the Termination Mode and Bypass Mode at the same
time. The measurements will not be accurate.
■ Termination Mode
The termination mode is used to check the cable status where the
camera and transmitter (Tx) are connected. The measurement is
possible when connected to an Intercoax ECP, ETP, EUP product
while in normal operation.
1. Connect the ITS-100 to the transmitter (Tx) using the correct
terminal.
Î
Do not connect ECP, ETC and EUP terminals at the same time.
Connect and measure one by one.
Error
Watt
Volt
Ohm
Error
Watt
Volt
Ohm
Power Supply
ITS-100
Tx / 카메라 설치 장소
ITS-100
ITS-100
ECP/EUP/ETP
Receiver
PoE Camera
PoE Camera
ⓐ
ⓑ
ⓐ
ⓑ
PoE IN
EUP
ETP
ECP
PoE OUT
PoE IN PoE OUT
PoE
Switch
PoE
Switch
Tx / Camera location
2. Once the ITS-100 is connected and running, the measurement
will appear.
3. Categories
Type of
measurement
Content
Unit LED
Power
available at
installation
place
Shows the standard voltage range of the PoE product
when operating normally. The value for the “Available
Power Consumption” where the tester (ITS-100)
is installed must be greater than the total power
consumption of the transmitter (Tx) and the camera
to avoid problems when installing the product
Watt
Voltage at
Installation
place
Shows the Voltage where the tester is installed
Shows the Voltage drop when the tester (ITS-100) is
on “Load”, not the Voltage at the Rx output, nor the
voltage at the maximum load
Volt
Cable
Resistance
Shows the cable resistance, measures from the
receiver (Rx) to the tester (ITS-100)
Ohm
■ Bypass Mode
It is used to check the cable connection to a PoE camera (PoE
product). The measurement is possible when PoE equipment
(product with PSE function such as a PoE switch for example) is
connected to a PoE camera and operating normally.
Do not connect products from the EUP series in this
mode, as it may cause damages to the device.
1. Connection
[CASE 1]: The ITS-100 tester is connected at the end of
the LAN cable, on the side of the PoE (PD) camera
ⓐ Connect the long-distance LAN cable to the ITS-100 Tester’s
PoE IN where the camera will be installed.
ⓑ Connect the PoE camera to the ITS-100 Tester’s PoE OUT.
Error
Watt
Volt
Ohm
Error
Watt
Volt
Ohm
Power Supply
ITS-100
Tx / 카메라 설치 장소
ITS-100
ITS-100
ECP/EUP/ETP
Receiver
PoE Camera
PoE Camera
ⓐ
ⓑ
ⓐ
ⓑ
PoE IN
EUP
ETP
ECP
PoE OUT
PoE IN PoE OUT
PoE
Switch
PoE
Switch
[CASE 2]: The ITS-100 tester is connected to the PoE [PSE]
ⓐ Connect the PSE product or the output terminal of the PoE
switch to the ITS-100 Tester’s PoE IN.
ⓑ Connect the long-distance LAN cable to the ITS-100 Tester’s
PoE OUT, then connect the PoE camera at the end of the cable.
Error
Watt
Volt
Ohm
Error
Watt
Volt
Ohm
Power Supply
ITS-100
Tx / 카메라 설치 장소
ITS-100
ITS-100
ECP/EUP/ETP
Receiver
PoE Camera
PoE Camera
ⓐ
ⓑ
ⓐ
ⓑ
PoE IN
EUP
ETP
ECP
PoE OUT
PoE IN PoE OUT
PoE
Switch
PoE
Switch
2. Once the ITS-100 tester is connected, wait a few moments
before the measurement appears.
3. Categories
Type of
Measurement
Content
Unit LED
Power
consumption
while in
operation
CASE 1: Shows the power consumption of the
camera (cable loss value not included).
CASE 2: Shows the cable specifications and total
power consumption, including the camera.
Watt
Voltage at
installation
place
Measures the voltage where the ITS-100 tester is
installed.
CASE 1: Shows the cable’s voltage drop when the
PoE camera is in operation.
CASE 2: Shows the output voltage of the PSE or the
PoE Switch.
Volt
Cable
resistance
Measures the cable resistance from the PSE or PoE
switch to the ITS-100 tester. If the LAN cable is
removed from the PoE OUT while the ITS-100 tester
is in operation, the resistance of the cable connected
to the PoE IN will be displayed (The resistance of the
cable connected to the PoE OUT is not measured).
Ohm
Display
Information
If the camera LAN cable is connected to the PoE OUT,
the display voltage drop and power consumption
supplied to the camera is displayed. If the camera
LAN cable is disconnected from the PoE OUT, the
PoE Output voltage and the cable resistance up to
the ITS-100 Tester’s PoE IN are displayed.
-
-
Remarks
Because of the cable voltage drop, the measurement in wattage/
voltage decreases compared to the power supplied to the cable
by the receiver (Rx).
This product is not a precision measuring device. The measurements
have a tolerance and are not guaranteed values.
The tester should be used during short periods of time, especially
when using the Termination Mode. The possibility of measurement
differences is greater if the tester is connected for a long time in
Termination Mode, because of heat generation.
Caution
Make sure to follow the instructions of the user manual when
installing and using the device.
Do not use the product for projects requiring guaranteed
measurements as this is not a precision measuring device.
Do not use the product for long periods of time.
Do not touch or handle the product and cables with wet hands,
as there are risks of electrocution.
Keep away from moisture and shocks.
This product is designed for indoor use. Do no use outdoors.
Do not use the product for any other purpose than that for which
it is designed.
Do not disassemble or modify this device.
Do not put any sticker or paint on the device.
If the device shows signs of defects or malfunctions, contact the
dealer where your purchased it or the service center.
Warranty
This device has passed the quality control and product inspection.
Please install and use according to the installation guide.
The warranty period for this product is 24 months from the date
of purchase.
If this device is defective or malfunctioning, please unplug the
power adapter immediately and contact dealer or service center.
Any damages or breakage from user’s abuse, accident,
modification or natural disasters will not be covered
manufacturer’s warranty.
Please visit below website for more detailed information.
Web: http://www.intercoax.com
Tel: +82. 31. 365. 3133~4
E-mail: [email protected]
Fax: +82. 31. 365. 3135
This device complies with part 15 of the fcc rules. Operation is subject to the
following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference
that may cause undesired operation
© Intercoax Co., Ltd.
