background image

. Regulations of repair guarantee 

We are responsible for the repair of complete machine for one  year. Guarantee of  laser tube (we are 
not  responsible  for  blowing  out  of  laser  tube  caused  by  high  water  temperature  and  frost  cracking 
caused by low water temperature) , mirrors and lens is three months, accessory parts is six months. 

Regulations of repair guarantee 

1. Within the guarantee period, our company will provide service for problems that appear in normal

using  conditions  for  free.  (This  point  is  valid  only  for  domestic  customers.  Certain  amount  of 
maintenance fees will be charged by the company when offering service out of China.). 

2. Certain amount of maintenance fees will be charged by the company when the guarantee period is

over. 

3. Our  company  will  not  provide  maintenance  and  repair  for  free  in  circumstances  that  the  sealing

paper is damaged caused by disassembly of the machine without authorization, the machine is not used 
in correct way, problems caused by calamities of nature and calamities imposed by other people, or the 
customer can not show us the repair guarantee certificate of the product. 

4. It  is  very  important  to  keep  the  serial  number  of  the  product  given  by  the  manufacturer  when  the

product  leaves  factory.  Only  when  information  contained  in  it  has  been  confirmed,  can  customers 
enjoy after-sale service provided by our company. 

5. The  manufacturer  has  the  right  to  modify  specifications  of  the  product  without  notification  to

customers in advance. 

6. The manufacturer only undertakes legal responsibilities for his products sold to customers, but is not

responsible  for  other  losses  caused  by  problems  of  the  machine  or  indirect  compensation 
responsibility. The manufacturer will not take any compensation responsibility for loss of commercial 
profits,  service  interruption  or  any  other  monetary  loss  caused  by  the  use  or  abnormal  use  of  the 
product. 

7. This certificate will be valid only after being stamped by distributor. It will be invalid if altered.

WWW.INTERLASER.RU

50

Summary of Contents for Rabbit HX-1630



















































Reviews: