background image

3-3  Features

•    The converter can be fully programmed by DIP Switches or by RS-232 using

•    Built-in battery rescue (pre-charging) function
•    Compatible with Lead Acid, LiFePO4, Gel and AGM batteries
•    High efficiency and high reliability
•    Withstand 2G vibration test
•    Advanced Protection Features

• Built-in Buck Boost Converter (12V to 12V)
• Voltage / Temperature Compensation with Battery Temperature Sensor (Optional)

- Input / Output Reversed Polarity Protection by fuse
- Input Over & Under Voltage Protection
- Output Over Voltage / Short Circuit Protection
- Internal Over Temperature Protection

3-4  Specification

MODEL

BBINT50A

OUTPUT

 
  Rated Power

 750W

  Absorp on  Voltage
  DIP S1

 0 : 14.4V ±1%
 1 : 14.7V ±1%

  Float Voltage

  DIP S2

 0 : 13.5V ±1%
 1 : 13.8V ±1%

  

Recharge Voltage

  DIP S3

 0 : 12V ±1%
 1 : 12.8V ±1%

  Charge Current
  DIP S4

 0 : 100%
 1 : De-Ra ng 50%

  Charging Control
  DIP S6 & S5

 00 : Charger 1 : bulk->absorp on->float->recharge
 01 : Charger 2 : bulk->absorp on->OFF->recharge
 10 : Power Supply 1 : Constant Voltage by DIP S2
 11 : Power Supply 2 : Constant Voltage by DIP S3

  

  

Level DIP S7

 N/A

  Ba ery Type

 Lead Acid/LiFePO4/Gel/AGM/Program(DIP S8)

  Fuse

 35A x 2

INPUT

  Voltage Range

 10V ~ 17V ±1%

  

Efficiency (Max.)

 92%

  Parasi c Curent
  ( Igni on OFF )

 < 5mA

  Type

 Ba ery / Alternator / DC Source

  Fuse

 35A x 3

7

      Intellitec MV GUI software BBINT50, downloadable from Intellitec MV Website

• Low temperature cut off and heater control for LifePo4 (requires temperature sensor) 

Summary of Contents for BBINT Series






















Reviews: