Refer to Figure 2.
The HIGH and LOW relay outputs can be combined, or used separately
(if two monitoring loops are available).
To connect the relays to a single monitoring loop, place a wire jumper
between the two common terminals. Connect the remaining NC
terminals to the monitoring loop.
To use the temperature probe remotely, connect the red wire to the (+)
input and black wire to the ( ) input.
Note: Wire connection to the terminal strip is not necessary for local temperature monitoring
(when the temperature probe PCB is installed on the display unit PCB).
TEMPERATURE DISPLAY
TEL:
(502) 266-5019
(800) 437-2002
FAX: (502)266-5259
2171 Watterson Trail
Louisville, KY 40299
Printed in Hong Kong
5-051-246-00 Rev B
Copyright 1992 IntelliSense Systems, Inc.
IntelliSense is a trademark of IntelliSense Systems, Inc.
All Rights Reserved
Wiring (Continued)
The T-1000 can display the temperature in degrees Fahrenheit or
Celsius. It is factory-set to display the temperature in degrees
Fahrenheit.
To change the display to degrees Celsius, perform the following steps
(refer to Figure 2):
1. Remove the front housing of the T-1000 display unit.
2. Remove jumper J2 and place it to cover the middle pin and the pin
labeled "C".
7. Replace the display unit front housing.
SPECIFICATIONS
Input voltage: 8.5 - 16 VDC
Input current: 35 mA
Operating temperature: 32
o
- 140
o
F (0
o
to 60
o
C)
Temperature sensing range: Local: 32
o
to 140
o
F (0
o
to 60
o
C)
Remote: -40
o
to 140
o
F (-40
o
to 60
o
C)
Accuracy: ±2
o
Fahrenheit (±1.1
o
Celsius)
Display: Three 7-segment displays
Alarm LEDs: 2 red LEDs indicating HIGH or LOW alarm
Relays: 2 Form-A relays
Relay contact rating: 30 VDC , 100 mA
TEMPERATURE ADJUSTMENT
To set the HIGH and LOW temperature parameters, perform the
following steps: (Refer to Figure 2.)
1. Remove the front housing of the T-1000 display unit.
2. To set the HIGH temperature parameter, remove the horizontal J1
jumper, and replace it vertically to cover the middle pin and the pin
labeled "HI."
3. With a screwdriver, turn the potentiometer labeled "HI" until the
desired "high" parameter appears on the temperature display.
4. To set the LOW temperature parameter, remove the J1 jumper,
and replace it vertically to cover the middle pin and the pin labeled
"LO."
5. With a screwdriver, turn the potentiometer labeled "LO" until the
desired "low" parameter appears on the temperature display.
Note: The two trip temperatures must be at least 2 degrees
(Fahrenheit) above and below the ambient temperature.
6. When both the HIGH and LOW temperature parameters have
been set, replace the jumper J1 back in its original position
(horizontally over the middle and side pins).
7. Replace the display unit front housing.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations
of the Canadian Department of Communications.
Le présent appariel numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A
prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada.
Seller warrants its products to be in accordance with its own plans and specifications and to be free from
defects in materials and workmanship under normal use and service for 18 months from the date
stamp control on the product; or for products not having an IntelliSense Systems date stamp, for 12
months from the date of original purchase, unless the installation instructions or catalogue sets forth
a shorter period, in which case the shorter period shall apply.
Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or
labor, any part which is proved not in compliance with Seller's specifications or proves defective in
materials or workmanship under normal use and service. This warranty is void if the product is altered
or improperly repaired or serviced by anyone other than IntelliSense factory service: 2171 Watterson
Trail, Louisville, KY, 40299.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FIT-
NESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. In no case shall Seller be liable to anyone for any
consequential or incidental damages for breach of this or any other warranty, express or implied, or
upon any other basis of liability whatsoever, even if the loss or damage is caused by Seller's own
negligence or fault.
Seller does not represent that its product may not be compromised or circumvented; that the product
will prevent any personal injury or property loss by burglary, robbery, fire, or otherwise; or that the
product will in all cases provide adequate warning or protection. Buyer understands that a properly
installed and maintained alarm system may only reduce the risk of burglary, robbery, or fire without
warning, but it is not insurance or guarantee that such will not occur or that there will be no personal injury
or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE, OR OTHER LOSS BASED ON A CLAIM THAT THE
PRODUCT FAILED TO GIVE WARNING. However, if Seller be held liable, whether directly or
indirectly, for any loss or damage arising under this Limited Warranty or otherwise, regardless of cause
or origin, Seller's maximum liability shall not in any case exceed the purchase price of the product,
which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive
remedy against Seller.
This warranty replaces all previous warranties and is the only warranty made by IntelliSense on this
product. No increase or alteration, written or verbal, of the obligation of this warranty is authorized.
LIMITED WARRANTY
