- 4 -
Copyright 2001 IntelliSense.
All rights reserved.
5-051-411-00 Rev C
SPECIFICATIONS
Range
:
25' (7.6 m) maximum
No minimum range
Operating Temperature:
32
o
to 120
o
F (0
o
to 49
o
C)
Storage: -4
o
to 122
o
F
(-20
o
to 50
o
C)
Alarm Duration:
5 seconds (unaffected by
alarm LED latching)
Alarm Relay:
Form C
125 mA maximum
25 VDC maximum
Tamper Switch:
Combination cover and
wall tamper
25 mA maximum
24 VDC maximum
Power Requirements:
8 - 14 VDC; 25 mA typical at
12 VDC, 35 mA max
AC Ripple: 4 Volts peak-to-peak
at Nominal 12 VDC
RFI Immunity:
30 V/m, 10 MHz - 1000 MHz
ESD Immunity:
10 kV,
Discharges of either polarity to
exposed surfaces
Dimensions:
3.86" H x 2.44" W x 0.86" D
(98 mm x 62 mm x 21.8 mm)
Weight:
3.2 oz., (90 g)
Packaged Product: 4.1 oz, (116 g)
FCC Notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: 1) Reorient or relocate the receiving antenna, 2) Increase the separation between the equipment and receiver,
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. The installer can also
consult an experienced radio/television technician for additional suggestions, if necessary.
IC Notice:
This digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil
numèrique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Protected Glass:
Minimum size for all types is 11"
(28 cm) square; Glass must be
framed in the wall of the room or
mounted in a barrier of 36" (0.9 m)
minimum width.
Thickness
Type
Minimum
Maximum
Plate
3/32" (2.4 mm)
1/4" (6.4 mm)
Tempered
1/8" (3.2 mm)
1/4" (6.4 mm)
Laminated
1
1/8" (3.2 mm)
9/16" (14.3 mm)
Wired
1/4" (6.4 mm)
1/4" (6.4 mm)
Coated
2
1/8" (3.2 mm)
1/4" (6.4 mm)
Sealed Insulating
1
1/8" (3.2 mm)
1/4" (6.4 mm)
2
For glass coated on the inner surface with 3M
®
scotchtint type RE35NEARL or Hardglass
®
Security Film, reduce maximum range to 15 feet (4.6 m).
1
Laminated and sealed insulating glass types are protected only if both plates of glass are
broken.
Accessories:
FG-701 Glassbreak Simulator
FG-SP1 Spacer Plate -
depth 0.6" (15.2 mm)
IntelliSense is a registered trademark of Honeywell, Inc.
Other trademarks are the property of their respective owners.
Note:
The FG-1025 Glassbreak Detector is designed for primary
perimeter security. For a complete security system, additional
interior protection devices are recommended.
Note:
For UL certificated installations, this detector must be
connected to a UL Listed power supply or UL Listed control
unit capable of supplying a minimum of four hours of standby
power.
Note:
The ULC label or listed marking on a product is the only
evidence provided by Underwriters Laboratories of Canada to
identify products that have been produced under the Listing
and Follow-up service.
Approvals/Listings:
FCC verified
IC verified
UL listed
ULC listed
CE Mark
(EMC Directive: residential,
commercial, light industrial)
C-Tick
