IntelliSAW 400.00152.0001 Integration Manual Download Page 3 | Manualshive

Page: 3 / 18

background image

Module Integration Manual

Page 3 of 18

Interrogator RF Board (400.00152.xxxx)

1

O

VERVIEW

This document outlines the integration requirements for the IntelliSAW INTERROGATOR RF
BOARDS used for passive, remote temperature sensing with a population addition for a partial
discharge receiver.



400.00152.0001 (ASSEMBLY, INTERROGATOR RF BOARD, PARTIAL DISCHARGE,

SMA)



400.00152.0002 (ASSEMBLY, INTERROGATOR RF BOARD, SMA)

The IntelliSAW RF card is a circuit board assembly integral to multiple current and future
products and is not sold or provided to third parties, except for integration into OEM equipment
designed in cooperation with, and manufactured on behalf of IntelliSAW, so as to account for all
constraints of the module.

«
1
2
3
4
5
...
»

Summary of Contents for 400.00152.0001



















Reviews:

No comments

Related manuals for 400.00152.0001

Brand: Vacon Pages: 64

Brand: U-Prox Pages: 3

Brand: U-Prox Pages: 2

Brand: WAREMA Pages: 112

Brand: WAGO Pages: 414

Brand: V2 Pages: 48

FT-2000 - MENU MODE LIST

Brand: Yaesu Pages: 56

Brand: Vag Pages: 15

Brand: Polycom Pages: 2

Brand: FUTABA Pages: 8

Brand: National Instruments Pages: 22

Brand: Variotech Pages: 24

Brand: H3C Pages: 15

Brand: Gliderol Pages: 2

Brand: Fancom Pages: 36

Brand: Beninca Pages: 8

DMX-LED-DIMMER X9 HR

Brand: DMX4ALL Pages: 14

Brand: Cypress Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands