IntelliPeak Ice Instruction Manual Download Page 33 | Manualshive

Page: 33 / 42

IntelliPeak Ice Instruction Manual Download Page 33

5. Expect Time: When the battery capacity and charge current values are

entered into the Four-Step Charge menu, Ice will calculate how much time
is “expected” to be needed to fully charge the battery while in four-Step
Charge mode. This time will be shown on the “expect time” line. Note: This
time does not include the temporary pauses that Ice needs to check battery
temperatures (if applicable) and so on.

6. Reserve Time:

Setting the

reserve time function for the
Four-Step Charge mode is done
in the main Four-Step Charge
screen as shown at right. Here,
the reserve time feature operates
the same way as in the CHARGE
/ DISCHARGE / CYCLE
screens… Set the reserve time
to be the number of minutes
before the next race starts plus
enough time to let the battery
cool beforehand. The

minimum

reserve time setting cannot be
lower than the calculated
“expect”

time above, and

maximum is 600 minutes. The reserve time does NOT include the time
needed for “discharge-before-charge” (see below). It is important to
remember that the reserve time will vary depending on the charge current
selection, capacity rating of battery, etc…

7. Trickle Charge: Rotate the dial to place the cursor in front of this line. This

sets the trickle charge current that will be applied to the battery after fast
charge ends. Press dial to highlight the value, and rotate to select the value
which ranges from 0-500mA.

8. Discharge > Charge: Rotate the dial to place the cursor in front of this line.

This “discharge-before-charge” simply instructs Ice to automatically
discharge the battery before starting the charge process. Press dial, then
rotate to either turn this feature “on” or “off.” The discharge current here is
automatically set to the maximum battery capacity entered in 2b (on page 32)
multiplied by 4. For simplicity, it is best to set this to “on” to empty the battery
before starting the Four-Step Charge mode.

9. Impulse Charge: Refer to diagram at right. This feature functions in Four-Step

mode only, and charges the battery at a current equal to the charge current
setting x 1.5 for 0.5 seconds, every 3 seconds. The charge current at all other

33

«
...
31
32
33
34
35
...
»

Summary of Contents for Ice











































Reviews:

No comments