Intellinet 524315 User Manual Download Page 115 | Manualshive

Page: 115 / 127

background image

Restore

Press 'Browse…' to pick a previously saved

Settings (2):

configuration file from your computer, and then
click 'Upload' to transfer the configuration file to
the router. After the configuration is uploaded, the
router's current configuration will be replaced by
the file you just uploaded.

Restore to

Resets all settings of the router to the factory default

Factory Default (3): values.

3-6 Firmware Upgrade

The firmware of the router is the equivalent of the operating system on
your computer. Firmware upgrades for this router may be available on
www.intellinet-network.com. If you experience technical difficulties, you
should first check if an updated firmware is available for the router and
install it using the firmware upgrade function.

Click the 'Tool' link located at the upper-right corner of the Web
management interface, then click 'Firmware Upgrade' on the left.

Click 'Next', and the following message will be displayed:

«
...
113
114
115
116
117
...
»

Summary of Contents for 524315
































































































































Reviews:

No comments

Related manuals for 524315

Brand: D-Link Pages: 168

AirPremier DWL-7700AP

Brand: D-Link Pages: 30

AirPlus Xtreme G DWL-2000AP

Brand: D-Link Pages: 28

Brand: Jabra Pages: 9

Brand: Jabra Pages: 9

Brand: TP-Link Pages: 74

Brand: Airlink101 Pages: 40

OmniAccess Stellar AP1301 Series

Brand: Alcatel-Lucent Enterprise Pages: 2

Brand: HiTi Digital Pages: 26

Brand: H3C Pages: 447

Brand: Gembird Pages: 57

Brand: Loopcomm Pages: 2

Brand: Arista Pages: 14

Brand: Linksys Pages: 17

Brand: D-Link Pages: 20

DI-624M - Wireless 108G MIMO Router

Brand: D-Link Pages: 12

Brand: D-Link Pages: 36

DI-624S - AirPlus Xtreme G Wireless 108G USB Storage Router

Brand: D-Link Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands