background image

sPecificAtions

Standards

 

• IEEE 802.11b (11 Mbps  

  Wireless Lan) 

• IEEE 802.11g (54 Mbps 

  Wireless Lan) 

• IEEE 802.11f (Inter-Access 

  Point Protocol, or IAPP) 

• IEEE 802.1x (Network Access 

  Control) 

• IEEE 802.1d (Spanning Tree) 

• IEEE 802.3 (10Base-T Ethernet) 

• IEEE 802.3u (100Base-TX 

  Fast Ethernet) 

• IEEE 802.3af (Power over 

  Ethernet) 

 

General

 

• Wireless frequency range: 

  2.412 – 2.484 GHz 

• Modulation technologies: 

  -  802.11b: Direct Sequence 

    Spread Spectrum (PBCC, 

    CCK, DQPSK, DBPSK) 

    - 802.11g: Orthogonal Frequency 

    Division Multiplexing 

• Channels: 

    -  USA/Canada: 11 channels 

    -  Europe: 13 channels 

    -  Japan: 14 channels 

• Data rates: 

  -  IEEE 802.11b (11 Mbps, 

    5.5 Mbps, 2 Mbps, 1 Mbps) 

   - IEEE 802.11g (54 Mbps, 48 

    Mbps, 36 Mbps, 24 Mbps, 

    18 Mbps, 12 Mbps, 9 Mbps,  

    6 Mbps) 

• Antenna: single detachable 

  dipole antenna with RP-SMA 

  connector, 2 dBi gain 

•  Output power: 

  -  OFDM: 23 dBm +/- 0.5 dBm 

    (54 Mbps, 200 mW max.) 

    -  CCK: 23 dBm +/- 0.5 dBm 

    (11 Mbps, 200 mW max.) 

• Output power settings: Highest, 

  High, Medium, Low, Lowest 

• Receiver sensitivity: -68 dBm  

  (54 Mbps); -85 dBm (11 Mbps) 

•  Maximum coverage distance:  

  100 m / 300 ft. (indoor),  

  300 m / 900 ft. (outdoor) 

• Wireless security: 

  -  WEP encryption (64/128 bit) 

    -  WPA (TKIP/AES), WPA2 

    (AES/mixed) 

    - IEEE 802.1x Radius client 

    with EAP-TLS authentication 

  -  Client access control through 

    media access control filter 

•  Wireless modes: 

    -  Access Point 

    -  WDS Repeater 

    -  WDS Bridge 

    -  AP Client (Infrastr  

    Ad-hoc) 

•  LAN ports: 

    -  RJ-45 10/100 Mbps data  

    port 

    - RJ-45 10/100 Mbps data   

    & power input port (PD port) 

•  Certifications: FCC Class B,  

  CE Mark, RoHS

LEDs

 

•  Power 

•  Status 

•  Wireless Link/Act 

•  WEP/WPA2 

•  MAC Ctrl 

•  Bridge 

•  LAN 1 Link/Act;  

•  LAN 2 Link/Act 

 

Environmental

 

•  Dimensions: 128 (W) x 89 (L)  

  x 27 (H) mm (5 x 3.5 x 1.1 in.) 

•  Weight: 165 g (5.8 lbs.) 

•  Operating temperature:  

  -5 – 55°C (23 – 131°F) 

• Operating humidity: 10 – 90%  

  RH, non-condensing 

•  Storage temperature:  

  -20 – 70°C (-4 – 158°F)

Power

 

•  External power adapter:  

  12 V DC, 1.0 A 

•  Via PoE PD port: 48 V, 0.2 A

Package Contents

 

•  High Power Wireless G  

  Access Point 

•  Power adapter 

•  Wall mounting hardware 

•  2 dBi detachable dipole  

  antennas with RP-SMA  

  connector  

•  Quick start guide 

•  Network cable: 91 cm (36 in.) 

• Stand for optional upright 

  installation

Summary of Contents for 503082









Reviews: