background image

20

A P P E N D I X   A

R e c o m m e n d e d   C a b l e   C o n f i g u r a t i o n s :

D C   S u p p l y   t o   I M S   D r i v e r

Cable length, wire gauge and power conditioning devices play a major role
in the performance of your IMS Driver and Motor.
NOTE: The length of the DC power supply cable to the IMS Driver should
not exceed 50 feet.
Example A demonstrates the recommended cable configuration for DC
power supply cabling under 50 feet long. If cabling of 50 feet or longer is
required, the additional length may be gained by adding an AC power
supply cable (see Examples B & C).
Correct AWG wire size is determined by the current requirement plus cable
length. Please see the IMS Driver Supply Cable AWG Table in this
Appendix.

Shield to Earth Ground

on Supply End Only

DC Voltage from

Power Supply

500 µf

Per Amp

+

-

Braided

Shield

Ferrite

Beads

π

 Type RFI Filter

 Required Current

+

-

To IMS Driver

Cable Length

less then 50 Feet

Shielded/Twisted Pair

(Wire Size from

IMS Driver Supply Cable AWG Table)

E x a m p l e   A   –   C a b l i n g   U n d e r   5 0   F e e t ,   D C   P o w e r

Summary of Contents for IM1007 I/IE

































Reviews: