background image

SAI2 Server Board TPS 

Jumpers and Connectors 

Revision 1.0 

 

 

 

47

 

4.2 Jumper 

Blocks 

Jumpers on the JP5 jumper block of the SAI2 server board set the system configuration. The 
jumpers are small plastic-encased conductors (shorting plugs) that slip over two jumper pins on 
a jumper block. 

On the SAI2 server board, the following jumper blocks are user-configurable. 

• 

CMOS and Password Clear 

• 

BIOS Recovery  

4.2.1 

Setting CMOS/Password Clear Jumper Block (JP5) 

Setting a jumper on system board jumper block JP5 enables the user to clear the CMOS or to 
clear a forgotten password. See the above figure for the location of the jumper block location. 
The following table lists the factory default settings for jumper block JP5, which are indicated in 
bold typeface. Procedures for setting the jumper on the block follow the table. 

Table 32. Jumper Block JP5 Settings 

Jumper Pin 

Numbers 

Function 

Jumper Position 

What it does at system reset 

1 - 2 

CMOS clear  

Open, Protect 

Preserves the contents of CMOS 

 

 

Closed, Erase 

Clears CMOS 

3 - 4 

Password protected 

Open, Normal 

Preserves the password 

 

 

Closed, Disable 

Disables the password 

5 - 6 

Reserved 

Open, Not Used 

No function 

7 - 8 

Reserved 

Open, Not Used 

No function 

9 - 10 

BIOS Recovery Boot 

Open, Normal 

BIOS Recovery Boot disabled. Normal 
operation. 

 

 

Closed, Recovery Boot 

If this jumper is set, BIOS recovery will be 
attempted from a bootable BIOS recovery 
floppy diskette. 

11 - 12 

Spare 

Closed, Spare 

Provides a spare jumper 

 

4.2.1.1 

Clearing and Changing a Password 

Clear and change a password as follows. 

1.  Power off the system, unplug the power cord, and remove the chassis panel. 

2.  Use needle-nose pliers or your fingers to remove the spare jumper from pins 11-12 on 

jumper block JP5. 

3.  Reinstall the jumper on pins 3-4 (Password Disable) of jumper block JP5. 

4.  Reinstall the chassis panel, plug in the power cord(s), and power on the system. 

5.  While waiting for POST to complete, press the 

F2

 key to enter BIOS setup. 

Summary of Contents for SAI2



















































































Reviews: