Intel M50CYP2UR Series System Integration And Service Manual Download Page 17 | Manualshive

Page: 17 / 162

background image

Intel® Server System M50CYP2UR Family System Integration and Service Guide

17

1.1

Reference Documents and Support Collaterals

For additional information, see the product support collaterals specified in the following table. The following
webpage provides support information for the M50CYP family:

https://www.intel.com/content/www/us/en/support/products/200321.html

Table 1. Intel® Server M50CYP Family Reference Documents and Support Collaterals

Topic

Document Title or Support Collateral

Document

Classification

For system integration
instructions and service guidance

Intel® Server System M50CYP2UR Family System Integration and Service
Guide

Public

For system integration
instructions and service guidance

Intel® Server System M50CYP1UR Family System Integration and Service
Guide

Public

For technical system-level
description

Intel® Server System M50CYP2UR Family Technical Product Specification

Public

For technical system-level
description

Intel® Server System M50CYP1UR Family Technical Product Specification

Public

For technical board-level
description

Intel® Server Board M50CYP2SB Family Technical Product Specification

Public

For server configuration guidance
and compatibility

Intel® Server M50CYP Family Configuration Guide

Public

For information on the Integrated
BMC Web Console

Intel® Integrated Baseboard Management Controller Web Console
(Integrated BMC Web Console) User Guide
For the Intel® Server Board D50TNP and M50CYP Families

Public

For BIOS technical information
on Intel® Server M50CYP Family

BIOS Firmware External Product Specification (EPS)
For the Intel® Server Board D50TNP and M50CYP Families

Intel
Confidential

For BIOS setup information on
Intel® Server M50CYP Family

BIOS Setup Utility User Guide
For the Intel® Server Board D50TNP and M50CYP Families

Public

For BMC technical information on
Intel® Server M50CYP Family

Integrated Baseboard Management Controller Firmware External Product
Specification
For the Intel® Server System D50TNP and M50CYP Families

Intel
Confidential

Base specifications for the IPMI
architecture and interfaces

Intelligent Platform Management Interface Specification Second
Generation v2.0

Intel
Confidential

Specifications for the PCIe* 3.0
architecture and interfaces

PCIe* Base Specification, Revision 3.0

http://www.pcisig.com/specifications

Public

Specifications for the PCIe* 4.0
architecture and interfaces

PCIe* Base Specification, Revision 4.0

http://www.pcisig.com/specifications

Public

Specification for OCP*

Open Compute Project* (OCP*) Specification

Intel
Confidential

TPM for PC Client specifications

TPM PC Client Specifications, Revision 2.0

Intel
Confidential

Functional specifications of 3

rd

Gen Intel® Xeon® Scalable
processor family

3rd Generation Intel® Xeon® Scalable Processors, Codename Ice Lake-SP
External Design Specification (EDS):

Document IDs: 574451, 574942,

575291

Intel
Confidential

BIOS and BMC Security Best
Practices

Intel® Server Systems Baseboard Management Controller (BMC) and BIOS
Security Best Practices White Paper

https://www.intel.com/content/www/us/en/support/articles/000055785/s
erver-products.html

Public

Managing an Intel Server
Overview

Managing an Intel Server System 2020

https://www.intel.com/content/www/us/en/support/articles/000057741/s
erver-products.html

Public

«
...
15
16
17
18
19
...
»

Summary of Contents for M50CYP2UR Series



































































































































































Reviews:

No comments

Related manuals for M50CYP2UR Series

Brand: IBM Pages: 908

Power 720 Express 8202-E4B

Brand: IBM Pages: 64

Brand: IBM Pages: 148

Brand: IBM Pages: 36

Brand: IBM Pages: 834

Brand: IBM Pages: 214

Eserver xSeries 360 Type 8686

Brand: IBM Pages: 74

Brand: Thecus Pages: 130

SuperServer 6123L-8R

Brand: Supero Pages: 105

Ultra Enterprise 3000

Brand: Sun Microsystems Pages: 48

PRIMERGY TX2540 M1

Brand: Fujitsu Pages: 92

PRIMERGY TX200 S5

Brand: Fujitsu Pages: 114

PRIMERGY TX300 S5

Brand: Fujitsu Pages: 142

PRIMERGY TX200 S6

Brand: Fujitsu Pages: 126

Server PRIMERGY TX1330 M1

Brand: Fujitsu Pages: 336

PRIMERGY TX300 S6

Brand: Fujitsu Pages: 122

Brand: Fujitsu Pages: 86

Brand: Fujitsu Pages: 109

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands