Intel IXF1104 Datasheet Download | Manualshive

Page: 105 / 231

background image

Intel

®

IXF1104 4-Port Gigabit Ethernet Media Access Controller

105

Datasheet

Document Number: 278757

Revision Number: 009

Revision Date: 27-Oct-2005

5.6.2.3

Receiver Operational Overview

The receiver structure performs Clock and Data Recovery (CDR) on the incoming serial data
stream. The quality of this operation is a dominant factor for the Bit Error Rate (BER) system
performance. Feed forward and feedback controls are combined in one receiver architecture for
enhanced performance. The data is over-sampled and a digital circuit detects the edge position in
the data stream. A signal is not generated if an edge is not found. A feedback loop takes care of
low-frequency jitter phenomenon of unlimited amplitude, while a feed forward section suppresses
high-frequency jitter having limited amplitude. The static edge position is held at a constant
position in the over-sampled by a constant adjustment of the sampling phases with the early and
late signals.

5.6.2.4

Selective Power-Down

The IXF1104 MAC offers the ability to selectively power-down any of the SerDes TX or RX ports
that are not being used. This is done via

“TX and RX Power-Down ($0x787)” on page 220

.

5.6.2.5

Receiver Jitter Tolerance

The SerDes receiver architecture is designed to track frequency mismatch, recover phase, and is
tolerant of low-frequency data jitter.

Figure 23

specifies the SerDes core receiver sinusoidal jitter

tracking capabilities.

1

0

1

1

2.0

20 mA

1

1

0

1

1.0

10 mA

1

1

1

0

0.5

5 mA

Table 29. SerDes Driver TX Power Levels

DRVPWRx[3]

DRVPWRx[2]

DRVPWRx[1]

DRVPWRx[0]

Normalized

Driver Power

Setting

Driver Power

NOTE: All other values are reserved.

«
...
103
104
105
106
107
...
»

Summary of Contents for IXF1104








































































































































































































































Reviews:

No comments

Related manuals for IXF1104

Brand: TC Electronic Pages: 2

Brand: Makita Pages: 2

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

Brand: EAW Pages: 6

Brand: EAW Pages: 6

Brand: H3C Pages: 33

S5500-SI Series

Brand: H3C Pages: 1217

Brand: 3Com Pages: 2443

Brand: H3C Pages: 3

Brand: H3C Pages: 4

Brand: Zenith Data Systems Pages: 64

ILDA Gem Laser projector tool

Brand: Stanwax Laser Pages: 3

MediaStream ConnectPlus 1000

Brand: Avid Technology Pages: 74

Brand: NETGEAR Pages: 2

Brand: Aleratec Pages: 12

Brand: CSS Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands