Intel DQ87PG Specification Download Page 69

Page: 69 / 102

Overview of BIOS Features

3.1

Introduction

The board uses an Intel Visual BIOS that is stored in the Serial Peripheral Interface

Flash Memory (SPI Flash) and can be updated using a disk-based program. The SPI

Flash contains the Visual BIOS Setup program, POST, the PCI auto-configuration

utility, LAN EEPROM information, and Plug and Play support.
The BIOS displays a message during POST identifying the type of BIOS and a revision

code. The initial production BIOSs are identified as

PGQ8710H.86A.

When the BIOS Setup configuration jumper is set to configure mode and the computer

is powered-up, the BIOS compares the CPU version and the microcode version in the

BIOS and reports if the two match.
The BIOS Setup program can be used to view and change the BIOS settings for the

computer. The BIOS Setup program is accessed by pressing the <F2> key after the

Power-On Self-Test (POST) memory test begins and before the operating system boot

begins.

Figure 18. Intel Visual BIOS Screen

Summary of Contents for DQ87PG







































































































Search results

Summary of Contents for DQ87PG

Reviews:

Related manuals for DQ87PG

Brands by name

Popular brands

Intel DQ87PG, Specification

Search results

Summary of Contents for DQ87PG

Reviews:

Related manuals for DQ87PG

Brands by name

Popular brands