Intel DQ87PG Specification Download Page 68

Page: 68 / 102

Intel Desktop Board DQ87PG Technical Product Specification

2.8

Reliability

The Mean Time Between Failures (MTBF) prediction is calculated using a parts count

method. The calculation is based on the Telcordia SR-332, Issue 2; Method I Case 3

50% electrical stress, 55 ºC ambient. The MTBF prediction is used to estimate repair

rates and spare parts requirements. The MTBF data is calculated from predicted data

at 55 ºC. The MTBF for the Intel Desktop Board DQ87PG is 258,525 hours.

2.9

Environmental

Table 36 lists the environmental specifications for the board.

Table 36. Environmental Specifications

Parameter

Specification

Temperature

Non-Operating

-20

C to +70

(Note)

Operating

C to +55

The operating temperature of the board may be determined by measuring the
air temperature from within 1 inch of the edge of the chipset/PCH heatsink and
1 inch above the board, in a closed chassis, while the system is in operation.

Shock

Unpackaged

50 g trapezoidal waveform

Velocity change of 170 inches/s²

Packaged

Half sine 2 millisecond

Product Weight (pounds)

Free Fall (inches)

Velocity Change (inches/s²)

<20

167

21-40

152

41-80

136

81-100

118

Vibration

Unpackaged

5 Hz to 20 Hz: 0.01 g² Hz sloping up to 0.02 g² Hz

20 Hz to 500 Hz: 0.02 g² Hz (flat)

Packaged

5 Hz to 40 Hz: 0.015 g² Hz (flat)

40 Hz to 500 Hz: 0.015 g² Hz sloping down to 0.00015 g² Hz

Note: Before attempting to operate this board, the overall temperature of the board must be above the

minimum operating temperature specified. It is recommended that the board temperature be at least

room temperature before attempting to power on the board.

Summary of Contents for DQ87PG







































































































Search results

Summary of Contents for DQ87PG

Reviews:

Related manuals for DQ87PG

Brands by name

Popular brands

Intel DQ87PG, Specification

Search results

Summary of Contents for DQ87PG

Reviews:

Related manuals for DQ87PG

Brands by name

Popular brands