Intel DB43LD Product Manual Download | Manualshive

Page: 26 / 80

background image

Intel Desktop Board DB43LD Product Guide

26

+5 V Standby Power Indicator

CAUTION

If the AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.

The Desktop Board’s +5 V standby power indicator, shown in Figure 4, is lit when
there is standby power still present on the board even when the computer appears to
be off. For example, when this green LED is lit, standby power is still present at the
memory module sockets and the PCI/PCI Express bus connectors.

Figure 4. Location of the +5 V Standby Power Indicator

For more information on standby current requirements for the Desktop Board, refer to
the Technical Product Specification by going to

http://support.intel.com/support/motherboards/desktop/

, finding the product, and

clicking on the Technical Documents tab.

«
...
24
25
26
27
28
...
»

Summary of Contents for DB43LD

















































































Reviews:

No comments

Related manuals for DB43LD

Z690 Phantom Gaming 4

Brand: ASROCK Pages: 109

Brand: Biostar Pages: 85

Brand: DFI Pages: 8

Brand: Sure Electronics Pages: 32

BrillianX 1S/2000

Brand: QDI Pages: 63

Brand: Intersil Pages: 26

Brand: Advantech Pages: 124

ISOFACE ISO2H823V2

Brand: Infineon Pages: 28

Brand: C&T Solution Pages: 48

Brand: Micrel Pages: 10

Brand: Gigabyte Pages: 38

Brand: Biostar Pages: 32

Brand: Systium Technologies Pages: 4

Brand: Gigabyte Pages: 96

Brand: Norco Pages: 60

Brand: DFI Pages: 177

GEO-SPOT GPS SW65/54

Brand: Watersnake Pages: 44

Brand: IMS Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands