Intel DB43LD Product Manual Download

Page: 17 / 80

Desktop Board Features

Legacy Input/Output (I/O) Controller

The I/O controller features the following:

•

Low pin count (LPC) interface

•

One serial port interface routed to an onboard header

•

Back panel PS/2 keyboard and mouse ports

•

One parallel port routed to the back panel

•

Serial IRQ interface compatible with serialized IRQ support for PCI systems

•

Intelligent power management, including a programmable wake up event interface

•

PCI power management support

LAN Subsystem

The LAN subsystem includes:

•

Intel

ICH10D

•

Intel 82567LM Gigabit (10/100/1000 Mb/s) Ethernet LAN controller

•

RJ-45 LAN connector with integrated status LEDs

The subsystem features:

•

CSMA/CD protocol engine

•

LAN connect interface between ICH10D and the LAN controller

•

PCI Express power management

For information about LAN software and drivers go to

http://support.intel.com/support/motherboards/desktop

LAN Subsystem Software

For LAN software and drivers, refer to the Intel Desktop Board DB43LD link on Intel’s
World Wide Web site at

http://support.intel.com/support/motherboards/desktop

Summary of Contents for DB43LD

















































































Search results

Summary of Contents for DB43LD

Reviews:

Related manuals for DB43LD

Brands by name

Popular brands

Intel DB43LD, Product Manual

Search results

Summary of Contents for DB43LD

Reviews:

Related manuals for DB43LD

Brands by name

Popular brands