background image

Intel Desktop Board D815EEA Product Guide

iv

Installing and Removing GPA Cards.......................................................................... 27
Removing the AGP Card Retention Mechanism ........................................................ 28

Installing and Removing Memory ....................................................................................... 28

DIMM Installation Guidelines ..................................................................................... 29
Installing DIMMs ........................................................................................................ 29
Removing DIMMs ...................................................................................................... 30

Installing the I/O Shield....................................................................................................... 30
Installing the Desktop Board............................................................................................... 31
Installing the Processor ...................................................................................................... 32
Removing the Processor .................................................................................................... 35
Replacing the Battery ......................................................................................................... 35
Connecting the IDE Cable .................................................................................................. 37
Setting the BIOS Configuration Jumper.............................................................................. 38
Clearing the Passwords...................................................................................................... 39

3 Upgrading the BIOS

Preparing for the Upgrade .................................................................................................. 41

Obtaining the BIOS Upgrade File .............................................................................. 41
Recording the Current BIOS Settings ........................................................................ 42
Creating a Bootable Diskette ..................................................................................... 42
Creating a BIOS Upgrade Diskette ............................................................................ 43

Upgrading the BIOS ........................................................................................................... 43
Recovering the BIOS.......................................................................................................... 44

4 Using the Setup Program

BIOS Setup Program Modes .............................................................................................. 45
Maintenance Menu............................................................................................................. 47

Extended Configuration Submenu ............................................................................. 48

Main Menu ......................................................................................................................... 49
Advanced Menu ................................................................................................................. 50

PCI Configuration Submenu ...................................................................................... 51
Boot Configuration Submenu..................................................................................... 52
Peripheral Configuration Submenu ............................................................................ 53
IDE Configuration Submenu ...................................................................................... 55

Primary/Secondary IDE Master/Slave Submenus ............................................. 56

Diskette Configuration Submenu ............................................................................... 57
Event Log Configuration Submenu ............................................................................ 58
Video Configuration Submenu ................................................................................... 59

Security Menu .................................................................................................................... 60
Power Menu ....................................................................................................................... 61
Boot Menu.......................................................................................................................... 62

IDE Drive Configuration Submenu ............................................................................. 63

Exit Menu ........................................................................................................................... 64

Summary of Contents for D815EEA



















































































Reviews: