Intel Cyclone 10 GX User Manual Download Page 1

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Cyclone 10 GX XCVR Toolkit Reference Design 

v17.1.1 User Guide

 

 

 
 
 
 
 
 
 

 

Date: January 2018 

 

Revision: 1.0 

 
 
 
 

©2017 Intel Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, INTEL, MAX, MEGACORE, NIOS, 
QUARTUS and STRATIX words and logos are trademarks of Intel Corporation and registered in the U.S. Patent and Trademark 
Office and in other countries. All other words and logos identified as trademarks or service marks are the property of their respective 
holders as described at www.altera.com/common/legal.html. Intel warrants performance of its semiconductor products to current 
specifications in accordance with Intel's standard warranty, but reserves the right to make changes to any products and services at 
any time without notice. Intel assumes no responsibility or liability arising out of the application or use of any information, product, or 
service described herein except as expressly agreed to in writing by Intel. Intel customers are advised to obtain the latest version of 
device specifications before relying on any published information and before placing orders for products or services. 

Summary of Contents for Cyclone 10 GX












Reviews: