Intel BLKD946GZISSL - CONROE LGA775 1066 800FSB DR2 A/V Lan SATA mATX 10Pack ACTIVE Motherboard Technical Product Specification Download Page 22

Intel Desktop Board D946GZIS Technical Product Specification 

22 

 

 

2D Graphics enhancements 

 

8, 16, and 32 bit color 

 

Optimized 256-bit BLT engine 

 

Color space conversion 

 

Anti-aliased lines 

 

Video 

 

Hardware motion compensation and iDCT for MPEG2  

 

Software DVD at 30 fps full screen 

 

Display 

 

Integrated 24-bit 400 MHz RAMDAC 

 

Up to 2048 x 1536 at 75 Hz refresh (QXGA) 

 

DDC2B compliant interface with Advanced Digital Display 2 or 2+ card 
(ADD2/ADD2+), support for TV-out/TV-in and DVI digital display connections 

 

Supports flat panels up to 2048 x 1536 at 75 Hz (when in dual-channel mode) 
or digital CRT/HDTV at 1920 x 1080 at 85 Hz (with ADD2/MEC) 

 

Two multiplexed SDVO port interfaces with 270 MHz pixel clocks using an 
ADD2/MEC card 

 

Dynamic Video Memory Technology (DVMT) support up to 256 MB 

 

Intel

®

 Zoom Utility 

1.5.1.2

 

Dynamic Video Memory Technology (DVMT) 

DVMT enables enhanced graphics and memory performance through highly efficient 
memory utilization.  DVMT ensures the most efficient use of available system memory 
for maximum 2-D/3-D graphics performance.  Up to 256 MB of system memory can be 
allocated to DVMT on systems that have 512 MB or more of total system memory 
installed.  Up to 128 MB can be allocated to DVMT on systems that have 256 MB but 
less than 512 MB of total installed system memory.  Up to 64 MB can be allocated to 
DVMT when less than 256 MB of system memory is installed.  DVMT returns system 
memory back to the operating system when the additional system memory is no 
longer required by the graphics subsystem.   

DVMT will always use a minimal fixed portion of system physical memory (as set in the 
BIOS Setup program) for compatibility with legacy applications.  An example of this 
would be when using VGA graphics under DOS.  Once loaded, the operating system 
and graphics drivers allocate additional system memory to the graphics buffer as 
needed for performing graphics functions. 

 

NOTE 

The use of DVMT requires operating system driver support. 

Summary of Contents for BLKD946GZISSL - CONROE LGA775 1066 800FSB DR2 A/V Lan SATA mATX 10Pack ACTIVE Motherboard

























































































Reviews: