Intel 81341 Developer'S Manual Download Page 268

Page: 268 / 1056

Intel

81341 and 81342—Address Translation Unit (PCI Express)

Intel

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

268

Order Number: 315037-002US

3.8.3

Transaction Ordering

Because the ATU can process multiple transactions, they must maintain proper

ordering to avoid deadlock conditions and improve throughput. The ATU transaction

ordering rules used by the 81341 and 81342 are listed in

Table 125

for the inbound

direction and

Table 126 on page 269

for the outbound direction. The tables are based

on the direction the transaction is moving, i.e. the data for inbound completion moves

in the same direction as the data for an inbound write or the address/command for an

inbound read.

Note:

Outbound Non-Posted Writes are the result of Internal Bus Memory writes that are

claimed by either the I/O translation window or the

Outbound Configuration Cycle Data

. Though these write requests arrive on the PCI Express Link as non-

posted write requests, it is important to note that from the Intel XScale

processor’s

point of view, these internal bus memory write requests are posted into the Outbound

ATU transaction queue. Thus, even though a write completion is returned to the ATU on

the PCI Express Link for outbound non-posted write request, the write completion is

not passed back through to the internal bus. Additionally, strong ordering between

outbound memory (posted) write requests and outbound non-posted write requests are

not

maintained as indicated in

Table 126 on page 269

For best performance, the user should designate the two Outbound Memory Windows

as non-cachable and bufferable from theIntel XScale

processor. This assignment

enables the Intel XScale

processor to issue multiple outstanding transactions to the

Outbound Memory Windows, thereby, taking full advantage of the ATU outbound queue

architecture. However, the user needs to be aware that the Outbound ATU queue

architecture does not maintain strict ordering between read and write requests as

described in

Table 126, “ATU Outbound Data Flow Ordering Rules” on page 269

. In the

event that the user requires strict ordering to be maintained, the user must change the

designation of this region of memory to be non-cachable/non-bufferable and enforce

the requirement in software.

Table 125. ATU Inbound Data Flow Ordering Rules

Row Pass Column?

Inbound

Write or

Message

Request

Inbound

Read

Request

Inbound

Configuratio

n Write

Request

Inbound

Read

Completion

Inbound

Configuratio

n or I/O

Write

Completion

Inbound Write or

Message Request

Yes

Inbound Read Request

Yes

Inbound Configuration

Write Request

Yes

Inbound Read

Completion

Yes

Yes?

Inbound Configuration

or I/O Write Completion

a. Inbound Completions for Configuration writes and I/O writes are not applicable since these transactions are

never passed back to the Internal Bus Requester (Intel XScale

processor). The reason is that from the Intel

XScale

processor’s point of view, these write requests are posted into the Outbound ATU transaction queue.

N/A

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands