Turning On & Basic Operations
En-36
1
Turn on the AV receiver and the connected TV.
On the TV, select the input to which the AV receiver
is connected.
2
Set the speaker setup microphone at the Main
Listening Position
a
, and connect it to the
Setup
Mic
jack.
The speaker setting menu appears.
Note
• The on-screen menus appear only on a TV that is connected
to
HDMI OUT MAIN
. If your TV is connected to other
video outputs, use the AV receiver’s display when changing
settings.
3
When you’ve finished making the settings, press
Enter
.
Perform the “Speaker Setup” according to your
speaker configuration:
–
Speakers Type (Front)
(
➔
page 58
)
–
Powered Zone 2
(
➔
page 58
)
–
Powered Zone 3
(
➔
page 58
)
–
Preout to External Amplifier
(
➔
page 58
)
–
Subwoofer
(
➔
page 58
)
If you use a powered subwoofer(s), go to step 4. If not,
go to step 5.
Speaker setup microphone
Setup Mic
jack
MultEQ XT32: Auto Setup
AUDYSSEY
Speakers Type(Front)
Powered Zone 2
Powered Zone 3
Preout to External Amplifier
Subwoofer
Normal
No
No
No
Yes
If “
Speakers Type (Front)
” is set to “
Digital
Crossover
”, a confirmation screen appears. Select
“
Next (2-7. Digital Processing Crossover Network)
”
to display the screen for Digital Processing Crossover
Network (
➔
page 62
). Continue with the settings.
4
Adjust the subwoofer volume level to 75 dB, and
then press
Enter
.
Test tones are played through the subwoofer. Use the
volume control on the subwoofer.
Note
• If your subwoofer does not have a volume control, disregard
the displayed level and press
Enter
to proceed to the next
step.
• If you set the subwoofer’s volume control to its maximum
and the level displayed is lower than 75 dB, leave the
subwoofer’s volume control at its maximum and press
Enter
to proceed to the next step.
5
Use
q
/
w
to select “Audyssey Quick Start” or
“Audyssey MultEQ XT32 Full Calibration”, and
then press
Enter
.
6
Press
Enter
.
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup starts.
Test tones are played through each speaker as
Audyssey MultEQ XT32 Room Correction and
Speaker Setup runs. This process takes a few minutes.
Please
refrain from talking
during measurements
and
do not stand
between speakers and the
microphone.
Do not disconnect the speaker setup microphone
during Audyssey MultEQ XT32 Room Correction and
Speaker Setup, unless you want to cancel the setup.
If you select “
Audyssey Quick Start
”, you will go to
step 9.
7
Place the speaker setup microphone at the next
position, and then press
Enter
.
Audyssey MultEQ XT32 performs more
measurements. This takes a few minutes.
8
When prompted, repeat step 7.
9
Use
q
/
w
to select an option, and then press
Enter
.
The options are:
`
Save
:
Save the calculated settings and exit
Audyssey MultEQ XT32 Room Correction and
Speaker Setup.
`
Cancel
:
Cancel Audyssey MultEQ XT32 Room
Correction and Speaker Setup.
Tip
• You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels by
using
e
/
r
.
Save
Cancel
MultEQ XT32: Auto Setup
AUDYSSEY
-- Review Speaker Configuration --
Yes
40Hz
40Hz
100Hz
None
100Hz
120Hz
2ch
Subwoofer
Front
Center
Surround
Front Wide
Front High
Surround Back
Surround Back Ch
To be continued
