background image

© INTEC Video Systems, Inc.  

Revision F May 2013

 

4

Warnings and Cautions 

 

Warnings 

 

Do NOT attempt to connect other 
electrical devices to the power wire 
harness of the Car Vision® System 
as this can cause an over current 
situation which can lead to electrical 
shock or fire. 

 

 

 

If at any time you see or smell smoke 
coming from the Car Vision® 
System, stop driving, exit the vehicle 
and disconnect main power. Check 
the system and remove any 
damaged components before you 
resume normal vehicle operation. 

 

 

 

Do NOT attach the wiring to any 
moving parts, across sharp edges or 
close to heat sources as this may 
cause shorting of the wires and may 
lead to a fire or electrical shock. 

 

 

 

When installing the camera system 
be certain that all items are secure. 
Items that are not secure or mounted 
in an unstable manner can come 
loose and cause damage or personal 
injury. 

 

 

 

When installing the system be sure 
to use only INTEC supplied brackets. 
The Car Vision

® 

camera must be 

insulated from the vehicle body. The 
supplied camera bracket provides 
the required insulation. Failure to do 
so could result in a fire and lead to 
property damage or personal injury. 

 

 

 

Do NOT install the camera in any 
area that allows it to extend out past 
the vehicle as this can cause injury if 
it were to come in contact with 
people walking around the vehicle.  

 

 

 

Never use fuses of a larger rating 
than those supplied with your Car 
Vision® System. Use of larger rated 
fuses can cause excessive current 
through the system if a short occurs 
and could lead to a fire. 

 
 
 
 
Cautions 
 
 

 

Confirm that the orientation of the 
image on the display is proper. Rear 
facing cameras should yield a mirror 
image, where items on the left of the 
vehicle appear on the left side of the 
monitor. 

 

 

 

Before you begin driving, be sure the 
display controls are adjusted 
properly. This will avoid unnecessary 
distractions while driving. 

 

 

 

Do NOT attempt to open or service 
your equipment. Removal of the 
product enclosure can lead to 
electrical shock. 

 

 

 

You should not attempt to make any 
adjustments to the Car Vision® 
System while driving as this can lead 
to an accident. Only make 
adjustments when the vehicle is 
stopped. 

 

 

 

Keep the Car Vision® System clean 
and free from dirt, snow and ice. If 
the camera glass or display panel 
becomes dirty, clean them before 
use. If they are covered with snow 
and/or ice, it should be cleared off 
before use. Failure to do so could 
lead to an accident.  

 

 

 

When running a cable from the 
exterior to the interior of a vehicle, 
care needs to be taken to seal the 
entry point. Failure to do so could 
allow in exhaust fumes, other toxic 
gases or water. 

 

 

Summary of Contents for CVC500AH Series
















Reviews: