background image

© INTEC Video Systems, Inc.  

Revision D Dec 2014

 

3

General Information 

Introduction 

Thank you for selecting an INTEC Car Vision® 
System. Before using your system, please be sure to 
read and understand these instructions carefully. If 
you have any questions or concerns, please do not 
hesitate to contact us toll free at 800-468-3254 
(west) or 800-522-5989 (east). 
 
This Guide is intended to provide you with 
information needed to successfully install and 
operate the CVC240HXL camera. 

 

Important Information 

Please read, follow and keep these instructions for 
future reference. A copy of these instructions should 
be left in the vehicle in which the system is installed. 
 
There are no user serviceable parts inside the 
system components. All service must be completed 
by authorized service personnel only. Please refer to 
the Warranty section described later in this manual.  
 
Always use the proper tools, wear protective clothing 
and take necessary precautions when working 
around electricity to prevent electrical shock. 
 
Use only INTEC specified and provided cables to 
connect the components of the system. Use of other 
than INTEC specified and supplied components and 
cabling could be dangerous and result in damage to 
the system components and void the warranty.  
 
Use only INTEC specified and supplied accessories 
and options when upgrading your system. 
 
Operating the camera system on too low or too high 
a voltage may damage the system. 
 
Always confirm the view provided by the camera is 
adequate for your needs prior to vehicle use. 
Adjustments to the camera viewing angle should be 
made before use, if necessary. 
 

Most states have laws pertaining to motor vehicles 
equipped with a video display within the driver’s field 
of vision, either directly or indirectly, unless the video 
display is used in conjunction with a back up safety 
camera to monitor the blind spots around the 
vehicle. INTEC’s products are specifically designed 
to enhance vehicle safety. Use of an INTEC display 
to view video in any manner other than intended 
requires installation in accordance with your state 
laws. 
 
We recommend the use of the optional Radar 
Sensors to enhance overall safety. 
 
Do NOT let the Car Vision® System distract you 
from driving safely. 

 

Certificates of Compliance 

 

This device complies with 
Part 15 of the FCC rules. 

 

 

 

 

Summary of Contents for CVC240HXL Series















Reviews: