background image

Customer Services (858) 578-7887 & (888) GO IN

TEC

IN

TEC

 Controls, 12700 Stowe Dr., Suite 110, Poway, CA 92064

Fax (858) 578-4633 & (888) FX IN

TEC

www.inteccontrols.com

Specification subject to change without notice.

Printed in USA 150109

Polygard® is a registered trademark of MSR

AT-1195_V3_UserManual

PolyGard

®

 O

2

 Transmitter

User Manual - AT-1195 V3

Page 09

9  Technical Data 

General sensor performances 

 

Gas type 

Oxygen (O

2

Sensor element 

Electrochemical, diffusion 

Measuring range  

0 – 25 vol. % 

Temperature range 

-4°F to 122°F (-20°C to 50°C) 

Pressure range 

Atmosphere ± 15 % 

Humidity 

0 – 99 % RH non condensing 

Storage temperature range  

23°F to 86°F (-5°C to 30°C) 

Storage time 

Max. 6 months 

Mounting height 

1.5 to 1.8 m (5 to 6 ft.) 

Accuracy 

± 0.1 vol. % 

Long-term output drift 

< 5% signal loss/year 

Response time 

t

90

 < 15 sec. 

Life expectancy 

2 years/normal operating environment 

Cross sensitivity

1

 

Concentration (ppm) 

Reaction (vol. %O

2

Carbon dioxide, CO

2

 

5 vol. % 

Electrical 

 

Power supply 

18 - 28 VDC/AC, reverse polarity protected 

(2-wire mode only VDC)

Power consumption (without options) 

- Analog mode 

- Bus mode 

 

22 mA, max. (0.6 VA) 

12 mA, max. (0.3 VA) 

Output signal 

 

Analog output signal 

Selectable: Current / tension 

                   Starting point 0 / 20 %  

(0) 4 – 20 mA, load 

 500 

(0) 2 - 10 V; load ≥ 50 k 

 

proportional, overload and short-circuit proof

Physical

 

 

Enclosure

2

 

Stainless steel V2A 

Enclosure colour

2

 

Natural, brushed 

Dimensions

2

 (H x W x D) 

113 x 135 x 45 mm /(5.35 x 4.5 x 1.8 in.) 

Weight

2

 

Approx. 0,5 kg (1.1 Ibs.) 

Protection class

2

 

IP 55  

Mounting

2

 

Wall mounting, pillar mounting 

Cable entry 

Standard 1 x M 20 

Wire connection 

Screw-type terminal min. 0.25 to. 2.5 mm

2  

24 to 14 AWG 

Wire distance (analog mode) 

Current signal ca. 500 m (1500 ft.) 

Voltage signal ca. 200 m (600 ft.) 

 

1

  The  table  doesn’t  claim  to  be  complete.  Other  gases,  too, can have an influence on the sensitivity. The mentioned 

cross sensitivity data are only reference values valid for new sensors.

 

2

 Indications only for option "stainless steel", for further types see datasheet “AT-DT Enclosure”. 

Specifications subject to change without notice. | USA 150109 | Page 9 of 13

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

 | relevantsolutions.com/inteccontrols

AT-1195_V3 – UserManual

Polygard® is a registered trademark of MSR | AT-1195_V3_UserManual

Specifications subject to change without notice. | USA 160104 | Page 9 of 13

12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN

TEC

 | relevantsolutions.com/inteccontrols

AT-1195 V3 – UserManual

PolyGard

®

 is a registered trademark of MSR-Electronic GmbH | AT-1195_V3_UserManual

INTEC Controls | 12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.INTEC | inteccontrols.com

Specifications subject to change without notice. | USA 200211 | Page 9 of 13

AT-1195 V3 – UserManual

Summary of Contents for MSR PolyGard AT-1195 V3














Reviews: