background image

Basics 

 

INSYS Modem 336 LL  

i-modul Modem 336 LL 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

Aug-06

 

1

 

Basics 

Leased line modems are used when a permanent connection between two data termi-
nals is required. 
For these connections no regular switched line is used, but a dedicated (leased) line. This 
can either be a line leased from Telekom, or just an unused pair e.g. on the premises. 
Leased line modems establish a connection via such a two wire line immediately after 
being switched on. 
Leased lines are sometimes “serviced” which means they don’t represent a direct two 
wire connection. The end terminals are supplied using a power supply unit. 
The INSYS Modem 366 LL / i-modul 336 LL supports both variants. They operate polarity-
independent which means that a1 and b1 are interchangeable. 

The two wire connection is the most used connection type. 

Unserviced line 

 

 
 
 
 

Serviced line 

 

i-modul 336 LL / 
INSYS Modem 336 LL 

Originate 

i-modul 336 LL / 
INSYS Modem 336 LL 

Answer 

LA 
LB 

LA 
LB 

LA 
 
 
LB 

i-modul 336 LL / 
INSYS Modem 336 LL 

Originate 

i-modul 336 LL / 
INSYS Modem 336 LL 

Answer 

LA 
 
 
LB 

Summary of Contents for i-modul 336 LL















Reviews: