Page 4 of 13
2634-222 - Rev: 2/11/2019 9:16 AM
Before Installation
CAUTIONS AND WARNINGS
Read and understand these instructions before installing and retain them for future reference.
On/Off Outdoor Module is intended for installation in accordance with the National Electric Code and local regulations in the United States or the
Canadian Electrical Code and local regulations in Canada.
On/Off Outdoor Module is not designed nor approved for use on power lines other than 120V 60Hz, single phase. Attempting to use On/Off
Outdoor Module on non-approved power lines may have hazardous consequences.
Prior to installing On/Off Outdoor Module, please review the entire installation procedure and take the following precautions:
-
Be sure On/Off Outdoor Module is connected to a 3-prong AC outlet that includes a Ground Fault Circuit Interrupt (GFCI) feature. If On/Off
Outdoor Module is plugged into an outlet without GFCI protection, make sure there is a GFCI device upstream (at another outlet closer to
the electrical panel or a GFCI circuit breaker).
-
Test your GFCI protection each time On/Off Outdoor Module is plugged in, as well as on a monthly basis. To test your GFCI protection,
make sure On/Off Outdoor Module is plugged in and the connected load is on. Then, push the TEST button on the GFCI outlet or circuit
breaker. This unit must stop operating. Wait about 5 seconds and then push the RESET button on the GFCI outlet or circuit breaker. On/Off
Outdoor Module will begin receiving electricity and the connected load will turn on. If the GFCI circuit does not perform in this manner, there
may be an electrical malfunction, increasing the probability of electric shock. Disconnect the power until the problem has been corrected.
Please see the instructions that came with your GFCI device for specific testing procedures. When in doubt of the GFCI device’s ability to
detect a ground fault, replace the GFCI device.
-
Don’t bury On/Off Outdoor Module, any electrical cable, or component connected to it. A buried power cord may result in electrocution if
improper cables are used or if digging occurs over the cable.
-
Don’t allow vegetation to grow on or around On/Off Outdoor Module
-
Don’t install On/Off Outdoor Module in a manner that allows water to accumulate around it
-
If an extension cord is used, the cord must be properly grounded. Be sure the extension cord is of adequate capacity to provide power to
your load. A “light-duty” or “medium-duty” extension cord may cause a voltage drop, which will cause overheating of the cable, plug, or
socket.
-
Don’t attempt to open On/Off Outdoor Module. The case is sealed and can’t be opened. There are no user-serviceable parts inside.
-
Don’t use On/Off Outdoor Module to control devices that preserve, maintain, or contribute to human or animal safety or life support
-
Don’t plug On/Off Outdoor Module into an outlet controlled by a switch because if the switch is inadvertently turned off, On/Off Outdoor
Module won’t have power
-
Don’t plug On/Off Outdoor Module into a filtered power strip or AC line filter
-
Be sure the device’s built-in switch is in the on position
-
Don’t exceed the load rating of On/Off Outdoor Module. Check and add up all the electrical devices that will be attached and make sure the
total does not exceed 12 Amps.
-
Don’t use any electrical cord or extension cord that is damaged or in poor condition
IMPORTANT!
If you have any difficulties or questions, consult an electrician. If you have any questions, call the INSTEON Support Line at 866-243-8022.
Installation
1)
Plug appliance/device (also called the load) you want to control into On/Off Outdoor Module outlet
2)
Plug On/Off Outdoor Module into unswitched wall outlet
Status LED will turn on solid green
The load will turn on. (If load does not turn on, tap Set button.)
3)
Allow On/Off Outdoor Module to hang down from outlet (see image)
Note: After completing installation, you will not be able to use the load’s built-in switch to control the load,
unless you have enabled Load Sensing. See
