instalight 1065 R B RGB(W)/TW 500mm
Safety instructions
Electrical devices may only be mounted
and connected by electrically skilled
persons.
Serious injuries, fire or property damage
possible. Please read and follow manual fully.
Only the manufacturer may exchange the
connecting cable. In case of damaged
connection cable, send the luminaire to the
central customer service office of the
manufacturer.
Do not operate the luminaire on a conventional
dimmer. Use DMX control device for dimming.
If the protective glass is damaged, replace the
entire luminaire.
Do not damage the powder coating. A damaged
powder coating can lead to corrosion.
Chemicals may endanger the corrosion
protection. Avoid contact with aggressive media
(e.g. acids).
These instructions are an integral part of the
product, and must remain with the end customer.
Device components
Figure 1
(1) Luminaire housing
(2) Protective glass (Light output)
(3) Clamping disc
(4) Mains connecting cable
(5) Data connecting cable
(6) Retainer clamp
(7) Data connector
(8) Mains connector
Function
Intended use
Compact LED Facade spotlight. To accentuate
architectural elements in indoor and outdoor areas.
Suitable for wall, ceiling and floor mounting.
Light technology
RGB:
12 LED light sources of different colours (4 x
red, 4 x green, 4 x blue). Each LED colour can be
controlled separately.
RGBW:
12 LED light sources of different colours (3 x
red, 3 x greed, 3 x blue, 3 x white). Each LED colour
can be controlled separately.
TW:
12 LED light sources (6 x warm white, 6 x cold
white). Each LED colour can be controlled
separately.
Beam characteristics dependant on choosen optics:
Asymmetrical, axially symmetrical or oval.
Beam angle and -characteristics see device label.
Control
Control of the individual light colors via DMX 512-A
(ANSI E1.11).
Parameterization via RDM (ANSI E1.20).
DMX channel mapping (RGB)
DMX channel
Description
1 (0...255)
Brightness red
2 (0...255)
Brightness green
3 (0...255)
Brightness blue
DMX channel mapping (RGBW)
DMX channel
Description
1 (0...255)
Brightness red
2 (0...255)
Brightness green
3 (0...255)
Brightness blue
4 (0...255)
Brightness white
DMX channel mapping (TW)
DMX channel
Description
1 (0...255)
Brightness warm white
2 (0...255)
Brightness cold white
DMX default settings
DMX start address*
1
Behaviour in case of
dmx data failure
The last received DMX
slot will be stored
*) Project-specific deviation possible. In this case the
default start address is marked on the luminaire.
Lamps / Maintenance
High-performance LED lamps. Average expected
lifespan (L80 / B10): 60,000 hours (@ 25 ° C).
The lamp may only be replaced by the manufacturer.
In case of damaged connection cable, send the
luminaire to the central customer service office of the
manufacturer.
Cleaning
Before cleaning, switch the luminaire off and let it
cool down. Clean the luminaire housing with a
moistened soft towel.
The protective glass can be cleaned using the same
cleaning agents approved for use on glass-ceramic
cooktops.
Information for electrically skilled
persons
Fitting and electrical connection
DANGER!
Electrical shock when live parts are
touched.
Electrical shocks can be fatal.
Before connecting the luminaires,
disconnect the supply line.
Mounting the luminaire
o
To install the luminaire, first loosen the side
clamping discs (3) using a TORX 30 pin wrench
and remove the retainer clamp (5) from the
luminaire housing (1).
o
Fit boreholes (Figure 2).
i
Use both of the external holes in the retainer
clamp at least for the installation.
o
Fasten the retainer clamps (5) to the installation
substrate using two suitable screws.
o
Insert the luminaire housing (1) into the retainer
clamp (5).
o
Push on the clamping discs (3) on both sides of
the retainer clamp and hand-tighten the screw
using a TORX 30 pin wrench.
Figure 2: Drilling dimensions
Figure 3: Mounting the luminaire
Electrical connection – General Instructions
Observe the maximum number of luminaires (n)
per circuit:
Circuit breaker
max. number of
luminaires
B10
18
C10
30
B16
30
C16
50*
*) Max. related to data cable: 32
Observe connection assignment (mains):
Connection
Contact ('S')
Wire col. ('L')
External cond.
L
Brown
Neutral cond.
N
Blue
Protective
cond.
/
Green-yellow
0000000037
0000000037
29.03.2017
instalight 1065 R B RGB(W)/TW
500mm
Art. No. il 1065 B...DX
Insta GmbH
Postfach 1830
58468 Lüdenscheid
T49 2351 936-0
www.insta.de
[email protected]
Operating instructions
